3onedata IES615-2D Series 사용자 설명서 - 페이지 4

{카테고리_이름} 3onedata IES615-2D Series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 3onedata IES615-2D Series 5 페이지. Managed industrial ethernet switch
3onedata IES615-2D Series에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (3 페이지)

페이지 인쇄

4. Power: Redundant, dual 12-48VDC power input

5. Environment working temperature: -40 75

Storage Temperature: -40 85

Relative humidity 5% 95%

DIN Rail Installation

In order to use in industrial environments expediently, the switch

adopt 35mm DIN-Rail installation, the installation steps as below:

1. Examine the DIN-Rail attachment

2. Examine DIN-Rail whether be firm and the position is

suitability or not.

3. Insert the top of the DIN-Rail into the slot just below the

stiff metal spring.

4. The DIN-Rail attachment unit will snap into place as shown

below.

Wiring Requirements

Cable laying need to meet the following requirements,

1. It is needed to check whether the type, quantity and

specification of cable match the requirement before cable

laying;

2. It is needed to check the cable is damaged or not, factory

records and quality assurance booklet before cable laying;

3. The required cable specification, quantity, direction and

laying position need to match construction requirements, and

cable length depends on actual position;

4. All the cable cannot have break-down and terminal in the

middle;

5. Cables should be straight in the hallways and turning;

6. Cable should be straight in the groove, and cannot beyond the

groove in case of holding back the inlet and outlet holes.

Cables should be banded and fixed when they are out of the

groove;

7. User cable should be separated from the power lines. Cables,

power lines and grounding lines cannot be overlapped and

mixed when they are in the same groove road. When cable is

too long, it cannot hold down other cable, but structure in the

middle of alignment rack;

8. Pigtail cannot be tied and swerved as less as possible.

Swerving radius cannot be too small (small swerving causes

terrible loss of link). Its banding should be moderate, not too

tight, and should be separated from other cables;

9. It should have corresponding simple signal at both sides of the

cable for maintaining.

Specification

Technology

Standard:

Support

IEEE802.3,

IEEE802.3u,

IEEE802.1Q, IEEE802.1p, IEEE802.1D/W

Protocol: ARP, ICMP, TCP, UDP, DHCP, DNS, HTTP, SW-Ring,

RSTP, SNMP

Flow control: IEEE802.3x, back pressure control

Function

Switch function: SW-Ring, QOS, 802.1QVLAN, RSTP, SNMP,

Port trunking, static multicast filter, port mirroring, port

flow statistics, upgrade online, up and download

configuration file, user name access system

SW-Ring: Support Single, Couple, Chain, Dual homing

Exchange attribute

100M forward speed: 148810pps

Transmit mode: store and forward

Switching fabric capacity: 1.0Gbps

MAC address table: 2K

Memory: 1Mbit

- 4 -

Interface

Electric port: 10Base-T/100Base-TX auto speed control, Half/full

duplex and MDI/MDI-X auto detect

100M optic fiber port: 100Base-FX, SC/ST/FC connector

Alarm port: 2 bit 7.62mm terminal block,

1 channel relay alarm output

Serial Port: RS-232 (DB9 male) or RS-485/422 (terminal block)

Serial

RS-232 signal: DCD, RXD, TXD, RTS, CTS, DTR, DSR, GND,

RS-485 signal: D+, D-, GND

RS-422 signal: T+, T-, GND, R+, R-

Parity: None, Even, Odd, Space, Mark

Data bit: 5bit, 6bit, 7bit, 8bit

Stop bit: 1bit, 1.5bit, 2bit

Band rate; 300 115200bps

RS-232 connector: DB9 male

IEEE802.3x,

RS-485 connector: 5 bit terminal block

RS-485/422 power isolation and signal isolation: AC2500V

Transfer distance

Twisted cable: 100M (standard CAT5/CAT5e cable)

Multi-mode: 1310nm, 2Km

Single-mode: 1310nm, 20/40/60Km

1550nm, 80/100/120Km

RS-485/422: 1200m

RS-232: 15m

LED indicator

Run indicator: Run

Power supply indicator: PWR1, PWR2

Ethernet interface indicator: Link (1~5)

Serial port indicator: Tx (1~2), Rx (1~2)

Power supply

Input voltage: 12 48VDC

Type of input: 4 bit 7.62mm pitch terminal block