3onedata IES615-2DI(3IN1) Series 빠른 설치 매뉴얼 - 페이지 2

{카테고리_이름} 3onedata IES615-2DI(3IN1) Series에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3onedata IES615-2DI(3IN1) Series 3 페이지. Managed industrial ethernet switch

페이지 인쇄

Step 1

Check if the DIN-Rail mounting kit is installed firmly.

Step 2

Insert the bottom of DIN-Rail mounting kit (one side

with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.

Tips:

Insert a little to the bottom, lift upward and then insert

to the top.

Step 3

Check and confirm the product is firmly installed on

DIN-Rail, then mounting ends.

【Disassembling DIN-Rail】

Step 1

Power off the device.

Step 2

After lift the device upward slightly, first shift out the

top of DIN-Rail mounting kit, then shift out the

bottom of DIN-Rail, disassembling ends.

【Power Supply Connection】



DC power supply

The series devices provide 4 bits power

supply input terminal blocks and two

independent DC power supply systems

for PWR1 and PWR2. The power supply

has nonpolarity and anti-reverse functions,

it can normally operate after reverse connection. Power

supply range: 12～48VDC

【Serial Port Connection】



3IN1 serial port

This series provide 5.08mm pitch 5 pins

industrial terminal blocks and support

RS-232/RS-485/RS-422 serial connection. Definition of pins

as the table below:

RS-485

D+

D-

GND

RS-422

T+

T-

GND

—

RS-232

GND

【Relay Connection】

Relay terminals are a pair of normally open

contacts in device alarm relay. They are open

circuit in normal non alarm state, closed when

any alarm information occurs. Such as: it's closed when power

off, and send out alarm. This series switches support 1

channel relay alarm information output, support DC power

alarm information or network abnormal alarm output, it can be

connected to alerting lamp, alarm buzzer, or other switching

value collecting devices for timely warning operating staffs

when alarm information occurs.

【DIP Switch Settings】

Provide 4-bits DIP switch for function setting,

where "ON" is enable valid terminal. DIP switch

definition as follows:

DIP

Definition

Operation

Reserved

Restore

Set the DIP switch to ON, the

factory

device will automatically reboot

defaults

and restore factory defaults, and

then set back the DIP switch.

Set the DIP switch to ON, the

device will be automatically

Upgrade

upgraded, and then set back the

DIP switch.

Reserved

【Console Port Connection】

The device provides 1 channel procedure debugging port

based on serial port, and can conduct device CLI command

line management after connected to PC. The interface adopts

RJ45 port, the RJ45 pin definition is as follows:

Pin No.

Definition

—

【Checking LED Indicator】

R+

R-

The function of each LED is described in the table as below:

—

LED

Status

OFF

ALM

OFF

RUN

OFF

Blinking

Link/ACT

Blinking

(1-5)

OFF

Blinking

OFF

Blinking

OFF

【Logging in to WEB Interface】

This device supports WEB management and configuration.

Computer can access the device via Ethernet interface. The

way of logging in to device's configuration interface via IE

browser is shown as below:

Step 1

Configure the IP addresses of computer and the

device to the same network segment, and the

network between them can be mutually accessed.

Step 2

Enter device's IP address in the address bar of the

TXD

RXD

GND

Description

PWR1 is connected and running

normally

PWR1 is disconnected and running

abnormally.

PWR2 is connected and running

normally

PWR2 is disconnected and running

abnormally

Power supply, port link alarm

Power supply, port link without alarm

The device is powered on or the device

is abnormal.

The device is powered off or the device

is abnormal.

System is running well.

Ethernet port connection is active.

Data transmitted

Ethernet port connection is inactive.

Serial port sends data abnormally

Serial port sends data normally

Serial port receives data abnormally

Serial port receives data normally