Atwood 87850 설치 및 운영 매뉴얼 - 페이지 2

{카테고리_이름} Atwood 87850에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atwood 87850 4 페이지. Bolt swivel, retaining ring swivel, tubular swivel, jacks

페이지 인쇄

TUBULAR SWIVEL JACKS

USE ONLY ATWOOD MOUNTING TUBES WITH ATWOOD TUBULAR SWIVEL JACKS

Bracket Mounting:

1. Assemble jack with tube (4A) and pin (4B) installed. Use this as a

templet prior to welding

2. Tack a weld at two spots at 180

mounting tube (4A) and the frame contact each other.

3. Separate jack from mounting tube (4A).

4. Weld completely around mounting tube (4A).

Jack Mounting:

1. Fit jack bracket over mounting tube (

2. Slide lock pin (

4-B) through jack and mounting tube holes.

FIG

3. Lock in place with hairpin cotter (

To Disassemble:

1. Remove hairpin cotter and lock pin.

2. Lift jack from bracket, use caution when removing the jack.

BOLT SWIVEL JACKS

Bolt around frame bracket:

1. Position jack on trailer tongue where jack can be freely swiveled.

2. Put bolts through bracket holes that are above and below frame.

3. Assemble furnished backing plates/lock washers/nuts on bolts (

4. Torque nuts to 20-25 ft. lbs.

Weld on frame bracket:

1. Position bracket with tabs located against bottom of tongue in a

location where jack can be freely swiveled (

2. Following

WELDING INSTRUCTIONS

with 1-1/2˝ minimum weld bead. Weld entire length of vertical

edges

5. Tabs on bottom of bracket locate bracket squarely

FIG

with bottom of frame.

3. Using provided socket head screws, attach jack to welded bracket

with open side of bracket toward the ground. Torque screws to 20-

25 ft. lbs. Make sure screw heads do not protrude above surface

of bracket.

OPERATION

THE CAPACITY OF THE JACK IS

IDENTIFIED ON THE TUBE OF

THE JACK -

PERSONAL INJURY

Never exceed the rated capacity identified on jack.

•

JACK CAPACITY DEFINITION

Working Capacity =

Maximum Load jack can support for castering and

Supporting Capacity =

Maximum Vertical Load that the jack can support.

PERSONAL INJURY / PRODUCT DAMAGE

Body and feet must be clear of trailer tongue when raising or lower-

•

ing jack.

ALWAYS FULLY RETRACT & SWIVEL JACK TO HORIZONTAL POSITION

•

use blocks for additional ground clearance, trailer can tip and fall.

DO NOT

•

Caster is intended to allow maneuvering of trailer for short distances on

•

smooth hard surfaces. Do not force caster over rough surfaces or obstacles.

Lower jack to minimum height before moving trailer on caster.

•

Do not use tow vehicle to move trailer with jack in vertical position.

•

Replace jack if worn, damaged or not operating freely.

•

When lowering jack, always provide footing (caster wheel or a jack

•

foot) beneath jack preventing dirt from entering center of ram.

apart at the point where the

4-A).

FIG

4-C) through end of lock pin.

FIG

5).

FIG

, attach bracket along top and bottom

CAPACITY

WARNING

easy lifting of a fully loaded trailer.

CAUTION

before towing trailer.

JACK MAY FALL IF NOT PROPERLY ENGAGED

SINGLE LOCK PIN STYLE - Locking pin end must be inserted fully into

•

bracket pin hole. Lock Pin shoulder must contact bracket tab before

use. Do not raise or lower tongue if the handle is not correctly locked.

Dirt, sand, ice, etc., must not obstruct the proper seating of lock pin.

•

Visually check that locking pin end(s) are inserted fully into bracket

•

receiving hole(s).

Never pull on lock pin(s) when any weight of the trailer is on the jack.

•

TEST JACK FOR LOCK PIN ENGAGEMENT ON ALL JACKS

Try to move jack to ensure proper engagement side to side with your

•

hand before applying load to jack.

Locking pin(s) end(s) must be inserted fully into bracket pin holes

•

6-B.

FIG

TOP WIND JACKS:

1. Pull handle up to horizontal position.

2. Turn handle clockwise to raise tongue, counter-clockwise to lower.

Prevent caster from rotating.

3. Push handle down along jack tube for storage.

SIDE WIND JACKS:

5).

1. Turn handle clockwise to raise.

FIG

2. Turn handle counter-clockwise to lower. Prevent caster from rotating.

RETAINING RING SWIVEL JACKS:

1. Pull on locking handle with one hand

2. Swivel jack to vertical or horizontal position

3. Release locking handle. It must engage hole(s) on assembled bracket

6-B.

FIG

4. Put jack in horizontal position before towing

TUBULAR SWIVEL JACKS:

1. Remove hairpin cotter and lock pin

2. Swivel jack 90˚

3. Replace lock pin and hair cotter

4. Put jack in horizontal position before towing

5. Replace lock pin and hair cotter

BOLT SWIVEL JACKS

1. Pull on lock pin

2. Swivel jack to horizontal or vertical position

3. Release lock pin. Pin must fully engage bracket attached to trailer

tongue

6-B.

FIG

4. When raising or lowering jack prevent caster from rotating while

cranking jack.

5. Put jack in horizontal position before towing

1. Lubricate jack at least every six months in the following manner.

a. Extend jack as far as possible.

b. Lubricate entire length of outside inner ram with SAE 30 heavy oil.

c. Squirt oil in oil hole or grease fitting provided at top of outer ram.

d. Clean dirt, mud or tar from jack.

2. For side wind jacks, follow procedure in

and lubricate gears with wheel bearing grease.

3. Should jack become difficult to operate: remove, clean and oil.

Inspect for bent or worn parts. Use only Atwood supplied parts for

replacement. Replace all bent or worn parts.

4. If it is not possible to get jack to operate freely, replace jack.

5. Should problems or questions arise, contact your dealer, the trailer

manufacturer or Atwood Service Department, 574-264-2131.

WARNING

6-A.

FIG

7 & 8.

FIG

4-B.

FIG

MAINTENANCE

1. Then remove cap

STEP

7 & 8.

7-B & 8-B.

FIG

7 & 8.

7-B & 8-B.

FIG