ATX DYNANO2E 설치 및 운영 매뉴얼 - 페이지 14
{카테고리_이름} ATX DYNANO2E에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ATX DYNANO2E 18 페이지. Dvis series nano-sized digital video insertion system rf output
CHAPTER 3: SET-UP AND CONFIGURATION
Saturation:
Audio Codec:
Audio Rate:
Program Identification
Program Number:
Video PID:
Audio PID:
PCR PID:
PMT PID [21-8190]:
Lock to V Sync:
Network Settings
Static IP Address:
Subnet Mask:
Default Gateway:
DNS IP Address:
DHCP Client Mode Enabled:
When all settings have been completed, click Submit to activate the changes. If the settings are not activated and you
close the screen, any new settings will not be applied and will be lost.
If all RF parameters are correct and the A/V ports are set up correctly, submission should enable the DVISn QAM modulator
and your new QAM channel should be available at the RF output port.
3.3
RF Output Connections
The output power level at RF OUT is set between 45 and 58 dBmV in the DVISn Settings screen.
3.4
Legacy Set-Top Box Settings
For systems using older set-top boxes such as DCT2000 and older Motorola STBs based on Cisco
Lock to V-sync and QBA Enable are selected on the DVISn Settings screen (a check mark appears in the box).
3-4
MDU Solutions
Allows modification of the video signal to increase or decrease saturation. There are
128 levels available (0-127).
A codec (compressor-decompressor) converts an audio signal to a specific file format
or streaming audio format that reduces the required storage space or bandwidth.
MPEG-1 supports stereo (two channel) signals while the AC-3 codec (licensed by
Dolby Laboratories) supports 5.1 surround sound.
Sampling rate at which an audio signal is encoded. The higher the bit rate, the better
the sound quality Audio rate options are 192, 256 and 384 kbps.
A unique number assigned to each program (1-65535).
The video PID (Packet Identifier) is a hexadecimal 13 bit number from 21 to 8190
that uniquely identifies a video transport stream in an MPTS (multi-program transport
stream) so that it can be filtered and routed appropriately.
The audio PID (Packet Identifier) is a hexadecimal 13 bit number from 21 to 8190 that
uniquely identifies an audio transport stream in an MPTS (multi-program transport
stream) so that it can be filtered and routed appropriately.
The PCR (Program Clock Reference) PID (Packet Identifier) is a hexadecimal 13 bit
number from 21 to 8190 that uniquely identifies the time base for synchronization of
individual frames or fields of the video stream and their associated audio.
The PMT (Program Map Table) PID (Packet Identifier) is a hexadecimal 13 bit number
that uniquely identifies a PMT in an MPTS (multi-program transport stream). The
PMT contains a data structure specifying which PIDs carry the video, audio and data
stream that collectively constitute the broadcast program.
Selects whether locking to vertical sync is enabled. This function is required when
DVISn signals are sent to some legacy STBs.
An IP (Internet Protocol) address is a numerical identification and logical address
assigned to devices participating in a computer network utilizing the Internet Protocol
for communication between nodes. When a computer is configured with a Static IP
address it always uses the same IP address. When a computer is configured with
Dynamic IP addressing it automatically procures an IP address when required.
A subnet mask allows the flow of network traffic between hosts to be segregated
based on a network configuration, improving network security and performance.
The node on the computer network chosen when an IP address does not belong to
any other entities in the Routing Table. Usually the node connecting internal networks
to the Internet and associated with a router and a switch.
DNS (Domain Name System) servers translate human-readable domain names into
machine-readable IP addresses and the reverse.
DHCP (Dynamic Host Configuration Protocol) automates network-parameter
assignment to network devices from one or more DHCP servers, making it easy to
add new machines to a network.
– DVIS Nano - Nano-sized Digital Video Insertion System RF Output – Installation & Operation Manual
®
standards, ensure that
®