Aube Technologies BDP-LX71 소유자 매뉴얼 - 페이지 2

{카테고리_이름} Aube Technologies BDP-LX71에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aube Technologies BDP-LX71 2 페이지. Aube technologies inc. programmable thermostat owner's guide

페이지 인쇄

5.4

Temporary Bypass

When the TH136 is in Auto or Frost Protection mode, you can bypass

the mode for two (2) hours. The TH136 will maintain the temperature

bypass for two (2) hours, then return to previous operating mode. Set

the temperature using these buttons

the bypassed mode will flash to indicate the bypass.

Pre-programmed Schedule

The TH136 programmable thermostat is pre-programmed with the

following schedule:

Time you wake

Time you leave

up and desired

and temperature

temperature

during your

absence

Programs 1 and 4 are repeated from Monday to Sunday.

Programs 2 and 3 are repeated from Monday to Friday.

Modify the Schedule

To modify the pre-programmed schedule, follow these steps:

Press the button associated with the program you wish to

modify.

Enter the program start time using the

Press the program button again.

Enter the desired temperature using the

Press

to exit.

NOTE:

After 60 seconds of inactivity, the thermostat will automati-

cally exit programming mode.

The TH136 thermostat is equipped with the Early Start function

(deactivated

default).

Programming.

Advanced Programming

You must hold the Auto button for 3 seconds to access the advanced

programming. Then, press Auto to select a menu.

Menus

Default

PPd MO

PPd TU

PPd WE

PPd TH

PPd FR

PPd SA

PPd SU

CPH

HLd

OF (off)

Press Auto until the desired menu is displayed.

To modify the default programming, use the

select from the available options.

Press

to exit.

NOTE:

Menus are detailed below.

8.1

Modify the Number of Programs per Day (PPd)

You can select the number of programs to be executed for each day

of the week. This means, you can run all 4 programs, only 2 (1st and

4th) or none (0).

NOTE:

When none (0) is selected, the TH136 will maintain the tem-

perature setpoint of the last program.

TH136

. The icon corresponding to

Time you return

Time you go to

home and

desired

overnight

temperature

buttons.

activate,

refer

Options

0, 2, 4

2, 3, 4, 5, 6

10°C

5°C to 28°C

OF / ON

buttons and

8.2

For greater flexibility, you can define the cycle that best suits your

requirements. The shorter the cycles, the greater your comfort.

However, your system will be activated more often when using

shorter cycles.

Cycles/hour

8.3

Use this menu to modify the Frost Protection setpoint associated with

the Frost Protection mode. The setting range is between 5°C and

28°C. Default: 10°C.

8.4

When Early Start is activated, the TH136 calculates the optimum start

time to obtain the desired temperature by the programmed set time.

bed and

8.5

For hot water installations, it is recommended that the pump be

activated at least 15 seconds every 24 hours to avoid any seizing.

Technical Specifications

Power

supply: 2 AAA (LR03) alkaline batteries

Max. resistive

Max. inductive

Remote

input: 12 VDC / ± 10% / 5 mA

Control

device: Electronic

Automatic

Storage

Operating

condensation

Temperature setpoint

Temperature display

Software: Class A

Protection

Environment: normally polluted

Warranty

Advanced

Aube warrants this product, excluding battery (if applicable), to be free from defects in the

workmanship or materials, under normal use and service, for a period of three (3) years

from the date of purchase by the consumer. If at any time during the warranty period the

product is determined to be defective or malfunctions, Aube shall repair or replace it (at

Aube's option).

If the product is defective,

(i)

return it, with a bill of sale or other dated proof of purchase, to the place from which

you purchased it, or

(ii)

contact Aube. Aube will make the determination whether the product should be

returned, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not

apply if it is shown by Aube that the defect or malfunction was caused by damage which

occurred while the product was in the possession of a consumer.

Aube's sole responsibility shall be to repair or replace the product within the terms stated

above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,

INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,

DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS

OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces and

states do not allow the exclusion or limitation of incidental or consequential damages, so

this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS

PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some

provinces and states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary

from province or state to another.

Technical Assistance

705 Montrichard

Saint-Jean-sur-Richelieu

Québec, Canada J2X 5K8

Tel. : (450) 358-4600

1-800-831-AUBE

Fax : (450) 358-4650

[email protected]

Modify the Heating Cycles (CPH)

Length

30 min.

20 min.

15 min.

Fuel, gas & electrical furnace

12 min.

10 min.

Modify the Frost Protection Setpoint (HLd)

Early Start (ES)

Pump Protection (PP)

load: 5A @ 240 VAC

load: 2A @ 240 VAC

action: Type 1B

temperature: -20°C to 50°C

temperature: 0°C to 50°C, 95% relative humidity without

range: 5°C to 28°C

interval: 0.5°C

resolution: 0.1°C

accuracy: ± 0.3°C

degree: IP 20

10 rue Ampère

95500 Gonesse

France

33 (0) 1 34 07 99 00

33 (0) 1 34 07 99 19

[email protected]

For more information on our products, visit us at

www.aubetech.com

400-136-001-C

Installation

Commercial unit

Direct wiring to circulator

2008-02-01

10.

11.

2/2