Auber Instruments EZboil DSPR310D 사용 설명서 - 페이지 10

{카테고리_이름} Auber Instruments EZboil DSPR310D에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Auber Instruments EZboil DSPR310D 14 페이지. For step mashing and boiling process automation
Auber Instruments EZboil DSPR310D에 대해서도 마찬가지입니다: 빠른 매뉴얼 (2 페이지)

페이지 인쇄

AUBER INSTRUMENTS

goto

rely

Knob

Relay 1

rl1

mode

off

Knob

lgc1

Logic mode

Rl_c

for relay 1

Knob

Relay turning-on

rlp1

steps

Knob

Pulse action for

lat1

relay 1

Knob

Alarm

sil1

suppression for

off

relay 1

Knob

ah1

off

Alarm 1

high limit

Figure 11. Flow chart for relay parameter settings

7. Application Examples

1) Use DSPR310D under single step mashing mode (similar to DSPR300)

Set the parameter as following:

Under PROG menu, set C – 1 as your mash temperature (like 122F), t – 1 to a

large time like 99:00; set all unused t – 2 ~ t – 6 to 00:00. Under MASH menu,

set EO to OFF.

Once powered up, this controller will maintain at the temperature of C – 1 for a

long time. You can manually end this process by press and hold Key B, of simply

turn off the controller.

2) Use DSPR310D as a manual power regulator (similar to DSPR1)

Set the parameter as following:

Mode = boil, tF = off, bAST = 0

To use it as manual regulator with temperature reading, please set it to boiling

mode. Disable timer event, and set boiling acceleration set temperature below

ambient temperature (or just zero).

8. Wiring Examples

Example 1. Here are two wiring diagrams of how to connect a DC triggered AC

SSR with this power regulator.

2018.08

Press

End

100

Press

Knob

Press

ap2

Alarm 2

pulse length

Press

Knob

Press

Alarm 1

ap1

pulse length

Knob

Press

Alarm 1

hy1

hysteresis band

0.3

Press

Knob

Press

al1

Knob Press

off

Alarm 1

low limit

Figure 13. Wiring examples of controlling a heater with SSR and DSPR310D in

a 120VAC system (upper) and in a 240VAC system (lower).

Example 2. Here is the wiring diagram of how to wire two external buzzers to

the controller.

120VAC

buzzer

RTD

Figure 15. Wiring example of external buzzers. Power supply for the controller

and heater is 240V AC. Power supply for two buzzers is 120V AC. AL1 buzzer

is for absolute temperature alarm. AL2 buzzer is for step alarm.

9. Beeping sound definition:

The pattern of the beeping sound for each condition is different. This section will

help user to tell what is the beeping for:

Legend:

―

1s short beep

――

2s long beep

―――――

5s long beep

●

1s short pause

●●

2s long pause

Step mashing mode:

1) Four 2s long beeps (―― ● ―― ●● ―― ● ――): It is separated by a 1s

short pause, a 2s long pause and another 1s short pause. It indicates that

current step is finished. Starting to heat up for the next step.

2) Three 1s short beeps (― ● ― ● ―): It indicates that the current mashing

step has started. The reading temperature has reached timer starting set point.

3) Eight 5s long beeps (――――― ●● ――――― ●● ―――――

●● ――――― ●● ――――― ●● ――――― ●● ―――――

●● ―――――): It indicates the whole program has ended. Both display will

flash "end".

Boiling mode:

1) Four 2s long beeps (――●―― ●● ――●――): It is separated by a 1s short

pause, a 2s long pause and another 1s short pause. It indicates that timer has

WWW.AUBERINS.COM

P10/14