Auber Instruments SYL-2615 사용 설명서 - 페이지 4
{카테고리_이름} Auber Instruments SYL-2615에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Auber Instruments SYL-2615 7 페이지. Wi-fi bbq controller
페이지 인쇄AUBER INSTRUMENTS
Pit: 73 Set:225
Food:71 Out:99
SE T
SE T
>Step: 1 Pit: 225
1-End: Fd Temp
/
>1-End: Fd Temp
SE T
1-Fd Temp: 170
/
SE T
> 1-Fd Temp: 170
Step: 2 Pit: 225
/
SE T
>Step: 2 Pit: 225
2-End:
Time
/
SE T
>2-End:
Time
2-Time:
6:00
/
SE T
>2-Time:
6:00
Step 3: Pit: 160
/
SE T
>Step 3: Pit: 160
3-End:
Time
/
SE T
>3-End:
Time
3-Time:
0:00
/
SE T
> 3-Time:
0:00
Back
/
SE T
> Back
Step: 1 Pit: 275
Figure 8. How to enter a cooking profile on SYL-2615 controller. The program
shown in Example 1 is used in this flow chart as a demo.
6.2 Set Parameters
To access the parameters, press and hold SET key for about 2 seconds.
Parameters are divided into two groups: "Control Config" and "System
Config".
6.2.1 Control Configurations
Parameters related control configurations during the smoking process are
listed under "Control Config" menu. Details of each parameters are listed in
Table 2. The flow chart in Figure 9 shows the operations of accessing and
adjusting the parameters in "Control Config".
Table 2. Parameters in Control Config menu.
Name
Description
AH (Pit)
Pit High Alarm
AL (Pit)
Pit Low Alarm
AH (Food)
Food High Alarm
Proportional
P
Constant
I
Integral Time
D
Derivative Time
T
Control Cycle Time
OL Switch
Open-Lid Detection
2019.07
>Step: 1 Pit: 225
>Step: 1 Pit: 275
1-End: Fd Temp
>1-End:
Time
1-Fd Temp: 170
1-Fd Temp: 175
>Step: 2 Pit: 225
>Step: 2 Pit: 230
>2-End: Fd Temp
>2-End:
Time
>2-Time:
6:00
>2-Time:
>Step 3: Pit: 160
>Step 3: Pit: 165
>3-End:
Time
>3-End: Fd Temp
> 3-Time:
0:00
> 3-Time:
Range
Initial
0 ~ 999
80
0 ~ 999
0
0 ~ 999
350
1 ~ 999
60
0 ~ 9999
1200
0 ~ 999
60
2 ~ 200
15
ON, OFF
ON
Save
SE T
Recall
SE T
Back
SE T
SE T
SE T
6:10
SE T
SE T
SET
SE T
0:10
SE T
Figure 9. Access the parameters in Control Config menu.
Note 1. AH (Pit): This is the high temperature alarm for pit temperature
(Probe 1). When pit probe reading is higher than AH (Pit) value, the buzzer
on the controller will go off and the LCD display will flash between the normal
display and the alarm display showing in Figure 10. The alarm has 1°
hysteresis. The user can mute the buzzer by pressing either the Up key or
the Down key. Temperature must move out of the hysteresis zone to activate
the alarm again. For example, if AH (Pit) is set to 290° F, the buzzer will go
off when Probe 1 reads higher than 291° F, and the buzzer will stop when
Probe 1 reads lower than 289° F. To disable AH (Pit) alarm, you can set it to
a large number, such as 750° F.
Figure 10. The LCD display when AH (Pit) is triggered.
Note
Note 2. AL (Pit): This is the low temperature alarm for pit temperature
1
probe (Probe 1). When pit probe reading is lower than AL (Pit) value, the
2
buzzer on the controller will go off and the LCD display will flash between
3
the normal display and the alarm display showing in Figure 11. The
alarm has 1° hysteresis. The user can mute the buzzer by pressing
4
either the Up key or the Down key. Temperature must move out of the
5
hysteresis zone to activate the alarm again. For example, if AL (Pit) is
6
set to 180° F. The buzzer will go off when pit temperature drop to 179° F;
7
it will stop when temperature rise above 181° F. The AL (Pit) alarm is
8
suppressed when the controller is just powered up. It will be activated
when the pit temperature has reached the target pit temperature. To
WWW.AUBERINS.COM
(Back), BGE,
WSM22,
Save PID Settings
WSM18,
4,5,6
(Back), BGE,
WSM22,
Recall PID Settings
WSM18,
4,5,6
Back to main
menu
SE T
SE T
SE T
Pit
High Alarm
Back
9
Back
9
SE T
SE T
P4/7