Auber Instruments TH100ACHIMDX 사용 설명서 - 페이지 2

{카테고리_이름} Auber Instruments TH100ACHIMDX에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Auber Instruments TH100ACHIMDX 2 페이지. Thermometer for stove pipe, chimney, w/ remote alarm

페이지 인쇄

AUBER INSTRUMENTS

Note 2. Set alarm for internal buzzer

The meter offers two alarms that can be set to turn on the internal buzzer at specific

temperatures. The first alarm is controlled by parameters AH1 and AL1. The initial

setting will turn on the buzzer at 481 ° F and off when temperature drops below 480° F.

The second alarm is controlled by parameters AH2 and AL2. The initial setting of the

second al a rm is deactivated. It can be set as low alarm to send warning.

AH1 and AH2 are the temperatures to turn the inernal buzzer on; AL1 and AL2 are the

temperatures to turn buzzer off. When AH1(2) >AL1(2), the alarm is set for absolute

high alarm as shown in Figure 4 below. When AH1(2) <AL1(2), the alarm is set for

absolute low alarm as shown in Figure 5 below. When AH1(2)=AL1(2), the alarm is

deactivated.

Example, if AH1=481, AL1=480, when the temperature goes up to 481° F, the buzzer

will be on; when the temperature drops down to 480° F, the buzzer will be off. If

AH2=180, AL2=185, when the temperature drops down to 180° F, the buzzer will be

on; when the temperature goes up to 185° F, the buzzer wil l be off.

User can press the shift key (>) to temporarily mute the buzzer sound. The alarm will

buzz again if the alarm set temperature is reached again. To permanently deactivate

the alarm, set AH1=AL1 or AH2=AL2. Please see flow chart in Figure 3 on how to set

the value.

The default setting is both internal and external buzzer are on when the

temperature is above 481 (SV+Hy, AH1); will be off when the temperature drops

down to 480 (SV, AL1).

Buzzer on

Figure 4. Absolute high alarm

5.2 System Configuration Parameters (accessed by code 0089)

Table 3. System configuration parameter setti n g

Code

Description

inty

Input Sensor Type

Inty

Output Mode

outy

Hysteresi s Band

atdu

Atdu

Ignore thi s setting

psb

Input Offset

PSb

External alarm type

Display Unit

corf

CorF

Exit

end

End

Parameter Display

Oper ation Mode

Enter Code

SET

0089

XXXX

SET

Figure 6. The system setup flow chart

Note 3. The value of outy should be 3.

Note 4. The default setting for the external buzzer is high limit alarm. The external

b u z z er w i l l be on when the tempeature is above SV+Hy will be off when the

temperature drops back to SV. The default setting for the Hy is 1.

2013.05

Buzzer on

Figure 5. Absolute low alarm

Setting Range

Initial

See Appendix

0, 1, 2, 3, 4, 5, 6

Note 3

0~9999

Note 4

0~200

-1000~1000

Note 5

0: low 1: high

Note 6

Note 7

° C 1:° F

inty

Output mode selection

SET

outy

Hysteresis Band

SET

XXXX

Autotune offset

SET

atdu

Input offset

SET

XXXX

psb

Heating/Cooling

SET

Display Unit(C/F)

SET

corf

end

Note 5. Calibration offset, PSb is used to set an input offset to compensate the error

produced by the sensor. For example, if the meter displays 5 º C when probe is in

ice/water mixture, setting PSb= -5, will make the controller display 0 ºC.

Note 6. Rd is for system function selection, Its value should be kept as 1 for high limit

alarm.

Note 7. Display unit selecti o n CorF: 0 for Celsius (° C); 1 for Fahrenheit (° F).

Additional note:

The remote alarm control output of this thermometer can also be used as a PID or

on/off control output. For detail s , please refer to Auber SYL-1614 manual.

Note

5755 North Point Parkway, Suite 99

Alpharetta, GA 30022 USA

Tech support: 770-569-8420, 404-983-8228

No part of this manual shall be copied, reproduced, or transmitted in any way

without the prior, written consent of Auber Instruments. Auber Instruments

retains the exclusive rights to all information included in this document.

WWW.AUBERINS.COM

Auber Instruments, Inc

P2/2