Auburn Gear Power Wheel Model 6 서비스 매뉴얼 - 페이지 2

{카테고리_이름} Auburn Gear Power Wheel Model 6에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Auburn Gear Power Wheel Model 6 4 페이지. Double reduction wheel drives with bearing locknut option
Auburn Gear Power Wheel Model 6에 대해서도 마찬가지입니다: 서비스 매뉴얼 (4 페이지), 서비스 매뉴얼 (4 페이지), 서비스 매뉴얼 (4 페이지), 서비스 매뉴얼 (4 페이지), 서비스 매뉴얼 (4 페이지), 서비스 매뉴얼 (4 페이지)

페이지 인쇄

IMPORTANT: All Power Wheel units and kits are shipped with a nameplate that includes the Auburn Gear part number and order code as shown.

Power Wheel

Example:

ORDER CODE: 6WB13156C

PART NO.: 6000236

SERIAL NO.: 143434

AUBURN, IN U.S.A.

STEP 1

If brake portion of drive is to be serviced: SAE A and SAE B MOUNT BRAKES

– Remove motor from planetary drive. SAE B MOUNT BRAKES – Temporarily

install two 1/2-13 x 1.25 screws into hydraulic motor mounting holes and torque

to 50 lb. ft. (67 Nm). These must be used to hold spring back-up plate in position

when parking brake assembly is removed from the drive. If the brake portion of

drive does not require service go to step 5.

STEP 2

SAE A MOUNT BRAKES – Remove the four socket head cap screws (27)

retaining the brake to the drive, leaving the two screws in line with the motor

mounting holes in place. These two screws hold the spring back-up plate in

position when the parking brake assembly is removed from the drive. SAE B

MOUNT BRAKES – Remove the four T-50 Torx head screws (27) holding the

parking brake assembly in position. (Some models may be equipped with socket

head cap screws). It may be necessary to lightly strike the piston assembly (26)

with a rubber mallet to loosen from spindle or cover.

STEP 3

Remove disc pack (25) from drive only if necessary. Be careful to maintain discs

in order.

STEP 4

If brake piston assembly (26) has been removed slide the coupling (23) and

retaining ring (24) from splines on input shaft (15). Remove sleeve bearing (22)

only if replacement is required.

STEP 1

Press new bearing cups (4) in each side of the hub (8). It is recommended that

bearing cups (4) and cones (3 & 9) be replaced in sets.

STEP 2

Assemble bearing cone (3) into cup (4) at seal end of hub (8) and press a new

seal (2) into hub (8).

STEP 3

Lubricate lips of oil seal (2) and lower hub (8) onto output shaft (1). Hub (8)

should be centered as it is lowered over output shaft (1) to prevent seal damage.

STEP 4

Assemble bearing cone (9) over output shaft (1) and into bearing cup (4). If

bearing (3, 4 & 9), hub (8) or output shaft (1) is replaced, a new retaining ring

(10) is required for proper bearing setting. Do not re-use snap ring after it has

been installed and removed from unit. Select the thickest retaining ring (10) that

can be assembled into ring groove of the splined end of output shaft (1) above

bearing cone (9). Bearing should have from .000 – .006 inches (0.00 – 0.15 mm)

of end play when proper retaining ring (10) is installed.

STEP 5

Clean mating surfaces and apply a bead of silicone sealant to face of hub (8)

that mates with ring gear (11). (See instructions on sealant package).

STEP 6

Assemble ring gear (11) to hub (8) being careful to align all the bolt holes.

IDENTIFICATION

In addition to the nameplate, Power Wheel drives are stamped with an identification number

which appears on the cover or hub flange as shown.

6000236-A-4-9

Example:

When ordering parts, the information included on the nameplate or the stamped identification

number is necessary to accurately identify the drive and obtain the correct replacement parts.

Once this information has been obtained, contact Auburn Gear for the appropriate parts list.

DISASSEMBLY OF POWER WHEEL

ASSEMBLY OF POWER WHEEL

STEP 5

Remove eight hex head bolts (19) and flat washers (18) from cover (16). Lift

cover (16) from assembly. Thrust washer (14) usually remains with cover (16).

STEP 6

Remove the splined input shaft (15) and lift sun gear (13) from carrier assembly

(12).

STEP 7

Remove carrier assembly (12) from ring gear (11).

STEP 8

Remove six hex head bolts (5) and flat washers (6) from hub (8). Pull ring gear

(11) from remaining assembly. It may be necessary to strike ring gear (11) with

rubber mallet to loosen from hub (8).

STEP 9

Remove retaining ring (10) from groove in output shaft (1). Pull output

shaft (1) from hub (8). N

: To remove retaining ring (10), use retaining

OTE

ring expander tool.

STEP 10

Remove oil seal (2) and bearing cones (3 & 9) from hub (8). Inspect bear-

ing cups (4) in hub (8) and remove only if replacement is required.

STEP 7

Install six grade 8 hex head bolts (5) and flat washers (6). Torque bolt to 52 – 60

lb. ft. (70 – 81 Nm).

STEP 8

Place carrier assembly (12) into ring gear (11) aligning the gear teeth. Carrier

splines mesh with splines on output shaft (1).

STEP 9

Install sun gear (13) into carrier assembly. Sun gear (13) should turn freely by

hand when assembled. Assemble splined input shaft (15) into sun gear (13).

STEP 10

Apply a bead of silicone sealant to cover face of ring gear (11). Secure thrust

washer (14) with tangs engaged in cover (16). N

cured to cover (16) with a small amount of grease or silicone sealant. Assemble

cover (16) to ring gear (11). Align cover (16) with hub (8) such that pipe plug

holes on cover (16) align with mounting holes in hub (8).

STEP 11

Install sleeve bearing (22) in cover (16). Assemble retaining ring (24) to adapter

coupling (23) and place into sleeve bearing (22) in cover (16). It may be neces-

sary to rotate coupling to align splines.

STEP 12

Install eight flat washers (18) and hex head bolts (19) and torque to 20 – 25 lb. ft.

(27 – 34 Nm) with dry threads. Lubed threads torque to 16 – 21 lb. ft. (22 – 28

Nm).

: Washer (14) can be se-

OTE