Aucma AUS-S2 사용 설명서 - 페이지 6

{카테고리_이름} Aucma AUS-S2에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aucma AUS-S2 7 페이지. Ultrafiltration under sink water filter system

페이지 인쇄

User's Manual

Direction for use

First step: after installation, before adding water, please check if all of the joints are

sealed.

Second step: open filtered water faucet, let the water flow for at least 15 minutes, to

wash the whole cabinet, until the outlet water is clean.

Third step: close the filtered water faucet to check if there's any water leakage. After the

above-mentioned operations, this equipment can be used.

Fourth step: if there's any water leakage condition, please turn off the inlet ball valve,

repair the leaking place.

Cautions

1.It is suggested to turn off the inlet water ball valve at night, and cut off the water source,

in case the pressure change in the night that may damage inner parts of the equipment or

causing water leakage.

2.Each day, when first using this equipment, open the inlet valve and the faucet, it can be

use normally after discharging 500ml of residual water.

3.If the water filter will not be used in a long time, please turn off the inlet valve.

4.It is normal to discharge black or white water for the first time.

Function Description

Running: when the power is on, all of the LED light will light up (the blue and red light will

blink in circle for 3 times), and goes into ventilation mode. It will go out in one minute if no

button is pressed.

Battery level: the warning starts when the battery has 10% left. It will beep for 3 times

continually in every 2 hours, and all the light will shine in circle from blue light, red light to

ventilation mode light.

Filter life expectancy: if the life expectancy of the filters are due, the corresponding red

light will blink and there will be voice warning. It will beep for 3 times in each 1 hour, the

filter red light will be light up for 1 second; after the filter is changed, the warning will be off.

Reset button: under the condition of powering on, short press the reset button, go into

filter function choosing, only the chosen filter light will be light up, press reset button in

order, and the filter light will be chosen in order from 1-2-3-1, then long press reset

button (over 3s), the chosen filter will be reset.

reset

Maintenance

(1)Replacement Period for Filter

The filter will accumulate various impurities after using for a period of time, which will

affect the outflow rate.

In order to maintain the normal outflow, the filter should be replaced regularly.

Filter Name

PPC Composite Filter

Replacement

6 Months

Period

The replacement period of the filter is completely different according to water quality and

the amount of pure water used. Therefore, the above suggested replacement period for

filter is just for reference.

Note: The filter should be replaced if the following situations occur:

1. The quality of filtered water is poor, the taste is bad, and the TDS value increases

significantly.

2. Outflow is significantly reduced, if it's not because of the low environmental

temperature and water temperature, it is necessary to check whether the filter or

membrane is blocked, and consider replacing the filter;

3. If the surface of the filter is discolored badly or the outer surface is covered with dirt;

4.The filter is blocked badly.

(2)Filter Replacement

In order to ensure that each filter of the product plays a good filtering effect and the

outflow meets drinking water standards, the user should replace or clean the filter

regularly. The filter should be replaced by professional.

(3)Steps To Replace the Filter:

1.First, close the water inlet ball valve and open

the water filter faucet to relieve pressure.

2.Take off the cover and rotate the disposable

filter counterclockwise by hand.

3. Remove the package of the new filter and

rotate it clockwise to the right position.

4. Open the inlet ball valve, check whether there

is leakage, open the water filter faucet, and the

new filter can be used after flushing.

5.Short press the reset button to start the filter

reset procedure, press successively until the

new filter is selected, then press the button for

3S to reset the filter.

SUF Filter

CTO Filter

12-24 Months

12 Months

A: Schematic diagram of

screwing filter

B: Schematic diagram of

screwed filter

Notes:

1. Gently twist the handle on the end

of the filter, to avoid damaging the

filter and its' positioning structure.

2. Referring to Figure A to screw in

the filter; When the filter is screwed

to the position shown in Figure B, the

filter has been installed. Please do

not screw forcefully again.