Dam Easy Flood Barriers DME01 사용 설명서 - 페이지 6
{카테고리_이름} Dam Easy Flood Barriers DME01에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dam Easy Flood Barriers DME01 13 페이지.
페이지 인쇄SECTION C: Installing the barrier(s)
1100mm –3300mm
43.3in – 129.9in
STEP 2B: EXTENDING THE SIDE PANELS – MULTIPLE BARRIERS
CAUTION: WEAR GLOVES TO PREVENT INJURY AT PINCH POINTS
1100mm –3300mm
43.3in – 129.9in
2B.2 Jack the Ratchet Handle to
2B.1. Hold Barrier #1 firmly in
position, pressing down at
Lifting Point. Position the
Direction Switch outwards
on Ratchet Handle
(towards user)
780mm –1100mm
2B.4 Barrier is secure when
2B.5 'Max' extension is marked
resistance is felt on the
Ratchet Handle, check that no
movement of the Barrier is
possible. Return the Ratchet
Handle to the verticle position
CAUTION/
Gradually extend each barrier in series to achieve
IMPORTANT
equalisation of pressure by each barrier for performance
10
1100mm –3300mm
43.3in – 129.9in
1100mm –3300mm
43.3in – 129.9in
780mm –1100mm
780mm –1100mm
30.7in – 43.3in
30.7in – 43.3in
1100mm –3300mm
43.3in – 129.9in
780mm –1100mm
1100mm –3300mm
1100mm –3300mm
1100mm –3300mm
43.3in – 129.9in
43.3in – 129.9in
43.3in – 129.9in
2B.3 Repeat positioning and
partially extend the Side
partial extension of barrier
Panels, until Barrier #1 stands
#2, #3 etc. in series (1B.2,
upright in position within the
1B.3, 2B1, 2B2)
780mm –1100mm
guide rails of the extension
pole(s), but no resistance
is felt
1100mm –3300mm
1100mm –3300mm
43.3in – 129.9in
43.3in – 129.9in
1
0
2B.6 Check that the door closes
at the top of each side
without interference.
panel. If the barrier is not
If there is interference, see
secure at this point, see
Section H Troubleshooting
Section H Troubleshooting
CONTINUE TO STEP 3,
2
INFLATE THE SEAL
1
3
4
0
bar
1100mm –3300mm
43.3in – 129.9in
STEP 3: INFLATING THE SEAL
CAUTION: NEVER INFLATE THE SEAL IF BARRIER(S) NOT SECURE IN A DOORWAY
780mm –1100mm
30.7in – 43.3in
1100mm –3300mm
43.3in – 129.9in
3.1 Open the Air Retention
Switch (vertical position)
2
2
1
1
3
0
4
0
bar
bar
2
3.4 Close the Air Retention
3
4
Switch (horizontal
bar
position), to avoid
accidental deflation
2
1
3
3.7 Check the Air Pressure Gauge at least every 2 hours initially,
4
0
bar
to ensure no drop in pressure. A drop in pressure may indicate
a problem, see Section H Troubleshooting
780mm –1100mm
SECTION C: Installing the barrier(s)
780mm –1100mm
3.2 Inflate the Seal using
the Pump Handle
780mm –1100mm
2
30.7in – 43.3in
1
3
4
0
bar
2
1
0
bar
780mm –1100mm
30.7in – 43.3in
3
4
3.5 Check the level of the
Barrier. Check that Barrier
has not raissed from
doorstep and is firmly
pressed down
TOP TIP: To prevent accidental deflation of the seal or unauthorised removal of the barrier,
optional accessory Dam Easy
®
lockable Security Cover is available for purchase
2
780mm –1100mm
30.7in – 43.3in
2
1
3
4
0
bar
2
1
3.3 Continue inflating until the Air
0
bar
Pressure Gauge is approx. 2 bar
(green region). If the pressure does
not increase, see Troubleshooting
3
4
3.6 Repeat for each barrier
for multiple barrier
installations. Installation
of the Barrier(s) is now
complete and ready to
protect the doorway
from flood water.
2
1
3
4
0
bar
3
4
11