Conairphone SW322 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Conairphone SW322에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Conairphone SW322 8 페이지. 10 memory speaker telephone

페이지 인쇄

OPERATION

Receiving a Phone Call

• Handset

1. When your phone rings, pick up the handset

and use it like any basic telephone.

2. Hang up the handset to release the

telephone line when conversation is

completed.

• Speakerphone

1. When your phone rings, press the SPEAKER

key (indicator light will come on).

2. Speak in the direction of the microphone.

3. Press the SPEAKER key to end your

conversation and release the telephone

line (indicator light will turn off).

Dialing a Call

NOTE: Before dialing, make sure the

Tone/Pulse switch is correctly positioned for

your type of service.

•Handset

Pick up the phone and wait for a dial tone,

then press the keys for the number you want.

Your telephone (pulse setting) uses electronic

pulses to simulate dialing action. Because of

this you might hear pulsing for a second or

two after the last button has been pressed.

•Speakerphone

1. Press the SPEAKER key and wait for dial

tone.

2. Press the keys for the telephone number

you wish to dial.

3. When the party you are calling answers,

you will hear them through the speaker.

4. When you have completed your call, press

the SPEAKER key to release the telephone

line.

NOTE: You may pick up the handset at any

time during your conversation. Lifting the

handset will automatically disconnect the

speakerphone. To resume speakerphone

operation, press SPEAKER key and return the

handset to the cradle.

Pulse/Tone Combination Dialing

Combination dialing is useful to subscribers

of rotary (pulse) service who wish to gain

access to various low cost long distance and

computer services otherwise unavailable to

them.

• With the TONE/PULSE switch in the pulse

(P) mode, dial your access number.

• Press the "*" key (your telephone will change

the dialing mode from pulse to tone and a four

second pause will be inserted automatically).

• Dial your code/authorization number.

• When call is completed, your telephone will

return to the pulse dialing mode automatically.

NOTE: Combination dialing can also be used

with the memory dialing feature for one touch

access of your long distance or computer

service.

KEY FEATURES

Last Number Redial

Your CONAIRPHONE

telephone remembers

the last number dialed. If the number you dial

is busy or not being answered, hang up. If you

want to redial the last number automatically,

press the REDIAL button. NOTE: You can

redial the same telephone number as many

times as required. However, once you dial

another number, the previous number is erased.

Ringer On/Off

Your CONAIRPHONE

telephone features a

harmonic dual tone ringer. When you don't

want to be disturbed, slide the switch to the

"off" position. Now you can still make outgoing

calls without being disturbed by incoming calls.

Receiver Volume Control

The receiver volume control is located on the

side of your handset (see diagram A).

This enables you to adjust the receiver

volume control from normal to high for a more

comfortable listening level.

Flash

The FLASH key can be used to retrieve a new

dial tone after ending a call. The FLASH button

is also a useful feature for special telephone

services such as call waiting and three party

calling. Press briefly, release and perform the

custom call procedure.

NOTE: Call waiting is a service of your local

telephone company.

MEMORY FEATURE

To Program

Your CONAIRPHONE

telephone is equipped

with 10 memories for programming your most

frequently dialed telephone numbers. You can

store up to 16 digits in each of the numeric

keys (0 through 9), by following the steps

outlined below:

1. Lift handset (releasing hook switch).

2. Press and release STORE key.

3. Press the keys for the telephone number

you wish to store.

4. Press and release the STORE key again.

5. Press the keypad number (0-9) you want

that telephone number stored in.

6. Your number is now stored.

7. To change a stored number, repeat the

same process. The new number will store

over the old stored number. A Memory Index

card is provided for your use in writing

down the person's name.

To Retrieve Memory Numbers

Keypad Memories: To retrieve numbers stored

in the keypad, pick up the handset and press

the MEM (Memory) key. Then press the keypad

number (0-9) which stores the telephone

number you want to dial. Your call will be

automatically dialed.

TROUBLE SHOOTING

GUIDE

Problem: No dial tone

• Check all modular plugs to be sure they

have clicked into place.

• Are cords damaged in any way?

• Try another phone jack. If your CONAIRPHONE

telephone works on another jack, there may

be a problem with your wiring.

Problem: I hear my phone dialing, but I can

not get past the dial tone.

• Check the tone/pulse switch. If positioned in

Tone (T) mode, switch to Pulse (P). You may

have pulse dialing service.

Problem: Phone does not ring.

• Is ringer switch set to the "Off" position?

• How many extensions are connected to your

line? If more than five telephones are

installed on the same line, you may need to

contact your local telephone company to

determine the maximum number of

extensions for your calling area.

Problem: The sound volume is too low.

• Is another extension off hook? If so, hang up

extension.

Problem: Memory dialing does not work.

• Carefully review STORE sequence and

reenter your programmed number.

• Did you pick up handset when programming

memory?