Dan D'Agostino Momentum 소유자 매뉴얼 - 페이지 3
{카테고리_이름} Dan D'Agostino Momentum에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dan D'Agostino Momentum 10 페이지. Hd preamplifier
Dan D'Agostino Momentum에 대해서도 마찬가지입니다: 소유자 매뉴얼 (13 페이지), 소유자 매뉴얼 (13 페이지), 소유자 매뉴얼 (15 페이지), 소유자 매뉴얼 (11 페이지), 소유자 매뉴얼 (11 페이지)
페이지 인쇄LegaL notifications
dan d'Agostino Master Audio Systems is a registered trademark of d'Agostino LLC.
The information in this owner's manual is subject to change without notice. Current
Version 1.0 of this manual was produced by the dan d'Agostino LLC engineering, sales
and marketing departments.
The information in this manual is the sole property of d'Agostino LLC. Any reproduction in
whole or part without the expressed written permission of d'Agostino LLC is prohibited.
no material herein may be transmitted in any way including either electronic or mechanical
methods for any purpose without expressed written permission of d'Agostino LLC.
CAUTION:
no uSer SerVICeABLe PArTS InSIde. do not open the amplifier's chassis
or remove any of its screws. Contact d'Agostino LLC or your dealer if you have service needs.
WARNING:
do not expose this preamplifier to moisture or excessive humidity, and do not
use it outdoors. Fire hazard may result.
The lightning flash with arrowhead, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating maintenance (servicing) instructions in
the literature accompanying the appliance.
UnPacKing anD instaLLation
Package contents
If any of the following items are missing, please contact your dealer:
1 Momentum preamplifier encased
in protective-static cling vinyl
1 content checklist
1 owner's manual
1 pair of white lifting gloves
1 microfiber cleaning cloth
Unpacking the Momentum preamplifier from the Pelican case
While the preamplifier is still in its case, please move it to a location near the place where
it will be installed. remove all jewelry including watches, rings and belts from your person
to avoid damage to the exterior of the preamplifier during the removal and installation. We
recommend that two people lift the Momentum preamplifier. Because it is machined from a
solid block of aluminum, it is much heavier than it looks.
Installation requirements
The Momentum's dense metal chassis makes it much heavier than the average preamp, so
make sure the surface that will support the Momentum preamplifier can safely hold its weight.
Adequate ventilation must be provided for the preamp. There should be at least 3 inches
of clearance on each side of the preamp and 3 inches of clearance at the top, and the
bottom vents must not be obstructed by thick carpet, dust, etc. We recommend that the
preamp be installed in an open equipment rack or on an amplifier stand to ensure proper
ventilation. The preamp may be installed in a closed cabinet in an equipment closet, but
the cabinet or closet must be designed with substantial ventilation at top and bottom;
active ventilation (i.e., powered fans) is preferred. do not place the preamp directly on a
carpeted floor.
The Momentum preamplifier is designed with special cone feet that screw into the bottom of
the preamp chassis and match up with indentations on the top of the power supply.
The bottom of the power supply has soft feet designed to isolate the preamp assembly from
vibration. (These feet will not stain or mar the surface underneath them.)
To attach the cone feet, use two people to turn the preamp chassis upside down and place
it on a soft but secure surface—a few towels draped over a sturdy table, for example. Screw
the feet all the way into the threaded holes on the bottom of the chassis. now place the
power supply in the place where you want to install the Momentum preamplifier. use two
people to turn the preamp back over again. Place it carefully atop the power supply chassis,
lining up the points of the cone feet with the indentations on the top of the power supply.
1 remote control
1 AC power cord
1 power-supply cable
2 single-ended (rCA)-to-balanced
(XLr) adapters