Concentric 10590 사용 설명서 및 부품 설명서 - 페이지 2

{카테고리_이름} Concentric 10590에 대한 사용 설명서 및 부품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Concentric 10590 4 페이지. Ac hydraulic power unit for auto hoists

페이지 인쇄

269xxxx

General Safety Information

DISCONNECT POWER BEFORE SERVICING THIS EQUIPMENT.

1. Follow all local electrical and safety codes, as well as the

National Electrical Code (NEC) and the Occupa tional Safety and

Health Act (OSHA).

2. For Single Phase Motors use 3-wire cords with 3-prong ground-

ing type plugs.

3. Make certain that wire size is adequate for horsepower require-

ments.

NOTE: Voltage drop increases with the length of power cord.

Larger wire diameter may be required.

4. Nameplate voltage must be available at the motor when it is

operating. Avoid voltage drop with adequate wiring.

5. Replace or repair damaged or worn power cord immediately.

6. The use of 3-prong single phase adapters in Canada is prohibited

by the Canadian Electrical Code.

7. DOUBLE CHECK ROTATION! Motor rotation is clockwise facing

drive end of motor.

8. On start-up, jog the motor to prime the pump to insure

adequate lubrication. After inlet line is full, motor may be oper-

ated at full speed.

CAUTION

NEVER RUN THE PUMP DRY.

9. Keep all lines as short as practical.

10. Never exceed the maximum operating pressure.

11. Do not overtighten fittings, bolts, etc., as this can damage the

units.

12. Provide adequate cooling for the hydraulic oil so as not to

allow oil and/or component damage due to excessive tem-

peratures. Excessively high operating temperatures can be

hazardous and may cause property damage and/or personal

injury.

13. Follow safety guidelines as recommended by Auto Hoist

Manufacturer.

Assembly

The 10590 Auto Hoist unit comes fully assembled from the factory.

Just remove the filler breather and fill the reservoir with oil.

Installation

1. Select a good location to mount the hydraulic power unit. This

style of unit is usually mounted on the side of the auto hoist

frame. Mount at least 18.0" above the floor. Choose a clean,

dry area with adequate ventiliation and preferably near the

electric power source.

2. This hydraulic power unit is designed for vertical mount with

motor feet up and reservoir down. Choose a flat mounting

surface to bolt motor base to. See unit dimensions for motor

base bolt pattern.

MODEL 10590

THIS UNIT IS INTERNALLY PLUMBED FOR VERTICAL MOUNTING

AS NOTED ABOVE. MOUNTING THE UNIT IN AN INCLINED PLANE

OR ANY OTHER POSITION WILL GREATLY REDUCE USABLE OIL

IN THE RESERVOIR. THIS CAN CAUSE OIL FOAMING, LIMITED

CYLINDER STROKE, ERRATIC MOVEMENT OR HYDRAULIC

COMPONENTS, AND PUMP FAILURE.

TO MINIMIZE CONTAMINATION PROBLEMS, DO NOT REMOVE

PLASTIC SHIPPING PLUG FROM HYDRAULIC UNIT UNTIL YOU

ARE READY TO INSTALL HOSE AND FITTINGS.

3. HYDRAULIC INSTALLATION - Make sure that work area and

hydraulic components are clean and free from dirt, lint, etc.

4. Remove the vent screw and washer that is located next to the

reservoir fill port with a phillips head screwdriver. When you

begin filling the reservoir with hydraulic oil, this vent will allow

trapped air in the reservoir to escape and reduce reservoir fill

time.

5. Fill the hydraulic unit reservoir through the 90° street elbow

(that you previously installed) with a good quality automatic

transmission fluid (ATF). Use a clean funnel fitted with a fine

mesh wire screen.

6. You will know that the reservoir is full when fluid begins to

dribble from the vent screw hole.

7. Reinstall the vent screw and washer.

8. Install plastic breather in 90° street elbow.

9. Remove 9/16/18 SAE O-ring shipping plug from power unit

and install appropriate hose and fittings.

DO NOT USE TEFLON TAPE! THIS UNIT IS EQUIPPED WITH SAE

O-RING TYPE PORTS.

DO NOT OVERTIGHTEN FITTINGS.

10. ELECTRICAL INSTALLATION - Motor nameplate voltage must

be available at the motor when it is operating. Choose a site

that avoids long power cord runs. Voltage drop increases

with the length of power cord. Larger wire diameter may be

required.

– 2 –

CAUTION