3onedata IES3012G-4GS 사용자 설명서 - 페이지 3

{카테고리_이름} 3onedata IES3012G-4GS에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 3onedata IES3012G-4GS 4 페이지. Industrial ethernet switch

페이지 인쇄

【LED Indicator】

LED indictor light on the front panel of product, the function of

each LED is described in the table as below.

System indication LED

LED

State

Description

Power is being supplied to power

input PWR1

Power is not being supplied to

OFF

power input PWR1

Power is being supplied to power

input PWR2

Power is not being supplied to

OFF

power input PWR2

When the alarm is enabled, which

any one way power supply fault

Alarm

Power supply normal, the alarm is

OFF

disabled.

System is not running well

ON/OFF

Run

System is running well

Blinking

Port connection is active

Link/ACT

Data transmitted

Blinking

(G1~G16)

Port connection is not active

OFF

【Installation】

Before installation, confirm that the work environment meet the

installation require, including the power needs and abundant

space. Whether it is close to the connection equipment and other

equipments are prepared or not.

1. Avoid in the sunshine, keep away from the heat fountainhead or

the area where in intense EMI.

2. Examine the cables and plugs that installation requirements.

3. Examine whether the cables be seemly or not (less than 100m)

according to reasonable scheme.

4. Power: support 12 ~ 48VDC power supply

5. Environment: working temperature: -40～75℃

Storage Temperature: -40～85℃

Relative humidity 5%～95%

DIN Rail Installation

In order to use in industrial environments expediently, the product

adopt 35mm DIN-Rail installation, the installation steps as below:

1. Examine the DIN-Rail attachment

2. Examine DIN Rail whether be firm and the position is

suitability or not.

3. Insert the top of the DIN-Rail into the slot just below the

stiff metal spring.

4. The DIN-Rail attachment unit will snap into place as shown

below.

Wiring Requirements

Cable laying need to meet the following requirements,

1. It is needed to check whether the type, quantity and

specification of cable match the requirement before cable

laying;

2. It is needed to check the cable is damaged or not, factory

records and quality assurance booklet before cable laying;

3. The required cable specification, quantity, direction and

laying position need to match construction requirements, and

cable length depends on actual position;

4. All the cable cannot have break-down and terminal in the

middle;

5. Cables should be straight in the hallways and turning;

6. Cable should be straight in the groove, and cannot beyond the

- 3 -

groove in case of holding back the inlet and outlet holes.

Cables should be banded and fixed when they are out of the

groove;

7. User cable should be separated from the power lines. Cables,

power lines and grounding lines cannot be overlapped and

mixed when they are in the same groove road. When cable is

too long, it cannot hold down other cable, but structure in the

middle of alignment rack;

8. Pigtail cannot be tied and swerved as less as possible.

Swerving radius cannot be too small (small swerving causes

terrible loss of link). Its banding should be moderate, not too

tight, and should be separated from other cables;

9. It should have corresponding simple signal at both sides of the

cable for maintaining.

【Specification】

Technology

Standard: IEEE802.3, IEEE802.3x, IEEE802.3u, IEEE802.3ab

Flow control: IEEE802.3x flow control, back press flow control

Exchange attribute

100M forward speed: 148810pps

1000M forward speed: 1488100pps

Transmit mode: store and forward

System exchange bandwidth: 56G

MAC address table: 10K

Memory: 12M

Interface

Gigabit RJ45 port: 10Base-T/100Base-TX/1000Base-TX auto

speed control, Half/full duplex and MDI/MDI-X auto detect

Console port: debug serial port carry out CLI command

Alarm port: 2 bit terminal block

1 channel relay alarm output

Transfer distance

Twisted cable: 100M (standard CAT5/CAT5e cable)