Ductless 16006 소유자 매뉴얼 - 페이지 4

{카테고리_이름} Ductless 16006에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ductless 16006 4 페이지. Wet-dry vacuum, hepa vacuum and toolsync tool activated vacuum

페이지 인쇄

Extension cord instructions:

How to Replace Filters:

Regular Wet/Dry Vacuum Filter

Use an outdoor, grounding type SJT

assembly:

extension cord of 16 gauge (up to 35

feet ) or 14 gauge ( any length ). The

Turn vacuum lid upside down on a flat

extension cord must employ a 3-prong

surface. Place the small, white

grounding type plug and a 3-pole recep-

secondary filter over the

tacle that accepts the machine plug.

spring mounted cage on

the underneath side of

Filters

the lid. Gently push the

Do not operate cleaner without filters

filter all the way on and

in place. To assure that your cleaner

compress the springs,

operates at peak performance, it is

then let off all pressure

imperative that you use only genuine

allowing the cage to push

Dustless Technologies filters.

the filter back out into a

relaxed position. Secure

Regular Wet/Dry Vacuum Filters:

filter firmly with the 7''

Primary and secondary filters should be

band clamp to the lid so

held in place by their respective band

particles are not allowed

clamps. There should not be any puckers

to go through to the

or wrinkles that will allow dust to travel

motor. Use a flat blade

through or suction will be reduced.

screwdriver for this clamp.

Micro Prefilter - Part #13141 is provided

with each vacuum. Packages of 2 are

Take the filter support basket with

available to purchase.

agitator rod and turn it upside down.

Put the agitator rod through the hole in

HEPA Filters:

the lid. The filter support basket rests

It is recommended to use part #13141 -

on top of the secondary filter with the

micro prefilter with your vacuum. Micro

agitator rod through the lid hole.

Prefilters #13141 are available. They are

recommended to be used on any fine

Place the primary filter over the filter

support basket and secondary filter.

dust application such as sanding drywall.

This is a disposable bag and should be

The side seam of the larger primary filter

thrown away when full.

should line up with the filter support

basket agitator rod and the filter is then

How to Clean Filters:

put around the large lip on the under-

Special note for HEPA filters: All HEPA

neath side of the lid and secured into

filters should be discarded after use, no

place smoothly with the 10'' band clamp.

attempt to clean filters should be made.

There should not be any wrinkles in the

fabric as they will affect the functioning

Turn the unit off then remove the brass

of the filters. The filter support basket is

agitator rod cover from the top of the

suspended between the two filters and

cleaner lid. The agitator rod will be

the agitator rod extends through the top

exposed. Lift the agitator rod about 1/2

of the lid. Use a flat blade screwdriver

inch and rock from side to side. The lid

for this clamp.

acts as a pivot point for the filter support

basket, located underneath the lid. The

Turn right side up and screw the brass

rocking motion of the basket agitates the

agitator rod cover into the top of the

primary filter to knock off the layer of

lid - only finger tight!! Do not

dust that has accumulated. This will

over tighten.

make the suction resume. After a period

of time, when suction is reduced and

cleaning the filters with the agitator rod

is not sufficient, the filters may be

replaced or laundered and reused.

Micro Prefilters are disposable and will

hold 20-30 lbs. of dust.

HOW TO USE

HEPA Wet/Dry Vacuum

Filter assembly:

The HEPA Filter is placed

over the crosspiece stud.

The threads will protrude

through the hole in the

middle of the HEPA filter.

Slide the provided rubber

washer (part #91522) over

the threads of the stud

with the rubber side

against the HEPA Filter.

Screw down the wing nut

(part #91523) and slightly

compress the rubber washer. It will

compress about 1/2 of its original

thickness. Next place the HEPA Filter

Cover Support on top of the HEPA filter

and finally place the HEPA Filter Cover

over the filter and cover. Attach the filter

cover with the 10" band clamp using a

flat blade screwdriver.

Turn right side up and screw the brass

agitator rod cover into the top of the

lid - only finger tight!! Do not over

tighten. This part must be in place to

maintain suction.

Dry Pickup:

Wet waste should be emptied from tank

but filters can remain in place.

Connect suction hose and appropriate

attachments for use. As suction is

reduced from fine material coating the

filters, shut off the unit to clean filters.

Remove the brass agitator rod cover and

rock the agitator rod from side to side to

clean filters and resume suction.

After Dry Pickup:

Disconnect cleaner from electrical outlet.

Release lid latches and remove cleaner

lid assembly as well as intermediate

cover from tank. Empty dry material from

the tank and intermediate cover.

To avoid back strain, do not lift a full

tank. First, scoop out enough debris to

make tank easier to lift.

Empty contents into a suitable receptacle.

Wet Pickup:

Dry waste should be emptied from tank

and intermediate cover but filters can remain

in place.

Should filters become wet, during use, dry both

filters thoroughly before continued use, consult

the trouble shooting guide (Filters get wet).

After Wet Pickup:

Unscrew drain

cap from bottom

of tank. This

drain is regulated so that

a floor drain can be used conveniently.

The liquid can be regulated from a drip to

a full flow.

The suction hose can be put in the drain cap to

drain liquid up to 12 feet away.

Rinse inside of tank thoroughly with clean water

particularly if spills or other substances other

than water have been

picked up. Wipe inside of tank dry. Screw drain

cap back on tightly so it is ready for use again.

Automatic Wet Shut-off:

When the tank is full of liquid, the automatic

shut-off mechanism will shut off cleaner pick-up.

When this happens, the motor sound will

become noticeably higher in pitch. Turn cleaner

off and empty tank to continue use.

Storage:

Disconnect cleaner from electrical outlet. Empty

tank. Rinse inside of tank thoroughly with clean

water particularly if spills or other liquid sub-

ToolSync Operation:

stances other than plain water have been picked

When the switch is in the I position,

up. Wipe inside of tank dry. If tank is stored

the vacuum will turn on but no power

with liquid left inside, the moisture may cause

will be applied to the vacuum ToolSync

damage to the motor and its internal parts.

outlet. When the switch is in the II

Wands and cleaning accessories as well as hose

position, power will be applied to the

store right on the accessory tray. Wands store on

ToolSync outlet on the vacuum. When

each of the back leg grooves provided.

the portable electric tool is activated,

the vacuum will turn on and run until

Lubrication:

the tool is turned off, then remain

The motor is equipped with bearings which con-

running for about 6 seconds to clear

tain sufficient lubrication for the life of the motor.

the hose. If the portable electric tool

The addition of lubricant could cause damage.

being used is rated 6-8 amps, the

Do not add lubricant to motor bearings.

vacuum will reduce power to the

If you have a problem:

vacuum to keep the total current to the

This appliance was inspected thoroughly and

tool and vacuum below 12 amps. The

was in good operating condition when it was

tool plugged into the vacuum will

shipped from the factory. If a minor problem

always receive full power. If a large

occurs, it usually can be solved quite easily

tool is attached to the vacuum outlet,

when the cause is found. Therefore, this Trouble

there may not be enough available

Shooting Guide is provided for you convenience.

current to supply the vacuum and the

ToolSync

Operation

Wireless ToolSync

Operation

Do not plug

Electric Tool

Start Module

into the vacuum.

vacuum motor will shut off. If this

occurs, a remote/wireless electric

start module will need to be used.

Some portable electric tools rated

less than 1 amp may not trigger the

automatic mechanism. When these

low amperage tools come into contact

with the work surface, they often

draw enough current to activate the

automatic start. When the vacuum is

started with an attached tool, and the

tool is turned immediately off (within

1-2 seconds), this will allow the

vacuum to remain running in a

"Clean-up mode". To clear "Clean-up

mode", simply turn the tool on for

more than 1-2 seconds, or turn the

vacuum to the off position. "Clean-up

mode" only works with a device

plugged into the vacuum outlet.