Duevi EZY-LAN 매뉴얼 - 페이지 5
{카테고리_이름} Duevi EZY-LAN에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Duevi EZY-LAN 12 페이지. Wireless alarm panel with ethernet + wi-fi + gsm + lte
Duevi EZY-LAN에 대해서도 마찬가지입니다: 사용자 설명서 (4 페이지), 사용자 설명서 (5 페이지)
페이지 인쇄Email
SMTP server settings that the control panel will
use for sending emails.
12 Settings menu (SETUP)
The settings menu, accessible by pressing the
icon
(double left arrow), contains the following
items:
•
Devices
•
Sectors
•
Actions
•
Users
•
Notifications
•
Programs
•
Cameras
•
Scenarios
•
Logic
•
Monitoring stations
•
Receive from panel
•
Send to panel
•
Save settings on disk
•
Load settings from disk
12.1 Devices (SETUP)
The DEVICES page contains the list of all the
devices associated with the control panel. In
factory conditions only the control panel is
present.
It is possible to add wireless devices or Shelly IP
devices.
Each device can contain one or more alarm zones
inside, as well as one or more outputs: for
example a MINI-C contains 4 zones (Internal
Contact, Vibration, External Contact, Shutter), a
MINI-M contains a zone (Contact), etc
PLEASE NOTE: The keyfob is not
considered a device, but must be added
within the individual user.
12.1.1 Wireless devices
It is possible to add new wireless devices in
several ways:
- wireless transmission of the enroll code
- manual entry of serial
- QR code scan (iOS and Android version only)
In the last two cases, the HW and FW versions of
the device will not be displayed.
Pressing the icon
the details of the zones / outputs of the device.
Pressing the icon
(trash can) deletes the device
from the control panel.
(info) expands the display of
Pressing the icon
settings, where you can change its properties
(they vary depending on the device).
NOTE: Some devices can receive
Firmware updates (eg control panel,
wireless sirens, video-pir). To update, on
the device settings page, press the icon
(gear) under the FW version (top right).
CONTROL PANEL
•
Device name: is the name with which the
device is identified in all menus, notifications,
events, etc
•
Panel language: ITALIANO, ENGLISH,
ESPANOL, FRANCAIS, GERMAN,
PORTUGUESE
•
Manumission Notify: none, events, events +
notifications, events + notifications + alarm
•
Wireless supervision: minutes of absence of
a device before giving the signal
•
Device loss notification: none, events, events
+ notifications, events + notifications + alarm
•
Power absence delay: minutes of external
power failure before giving the signal
•
Visual and sound signals for: Alarm L1, Panic
alarm, Arming, Disarming, System status
•
On-board button zone settings
SENSORS
•
Device Name: is the name with which the
device is identified in all menus, notifications,
events, etc
•
Tamper: enables / disables the device tamper
signal
•
Wireless supervision: enables / disables the
device presence control
•
Masking control: enable / disable the device
masking control
•
Individual zone setting:
-
Zone name
-
Zone type: Volumetric, Door, Shutter,
Vibration, Button
-
Alarm level: select the alarm level of the
zone between High (L2) / Low (L1)
-
Zone
mode:
Silent, 24H, Panic, Only use for logic
The zone set as mode "Only use for
logic" cannot be managed within the
sectors as an alarm zone, but can
only be used within a Logic (see
"Logic" section).
-
Manually excludable: enables / disables
the possibility for the administrator user to
manually exclude the zone
(gear) enter the device
Instantaneous,
Delayed,