Danfoss 084B4081 설치 매뉴얼 - 페이지 10

{카테고리_이름} Danfoss 084B4081에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Danfoss 084B4081 16 페이지.

페이지 인쇄

Menu survey

Menu set via display

Parameters

Function

Normal operation

Temperature (setpoint)

Thermostat

Differential

Max. limitation of setpoint setting

Min. limitation of setpoint setting

Temperature unit (°C/°F)

Correction of the signal from S4

Correction of the signal from S3

SEr: Manual control (-1), OFF: Stop control (0), ON:

Sta<rt control (1)

Displacement of reference during night operation

Define thermostat function

1=ON/OFF, 2=Modulating

Definition and weighting, if applicable, of thermostat

sensors - S4% (100%=S4, 0%=S3)

Time between melt periods

Duration of melt periods

Temperature setting for thermostat band 2.

As differential use r01

Definition and weighting, if applicable, of thermostat

sensors when night cover is on (100%=S4, 0%=S3)

Heat function

Neutral zone between refrigeration and heat function

Time delay when switching from refrigeration to heat

function

Food type: use settings listed in table

Min. limit for S4 temperature

Alarms

Delay for temperature alarm

Delay for door alarm

Delay for temperature alarm after defrost

High alarm limit for thermostat 1

Low alarm limit for thermostat 1

High alarm limit for thermostat 2

Low alarm limit for thermostat 2

Alarm time delay or signal on the DI1 input

Alarm time delay or signal on the DI2 input

Signal for alarm thermostat. S4% (100%=S4, 0%=S3)

Compressor

Min. ON-time

Min. OFF-time

Time delay for cut-in of comp. 2

Switch mode for 2 compressor operation.

= 1 sequentially. = Cyclic 2

Defrost

R-W

If the operation is limited by a setting of one or more passwords, reading and setting the parameter will be limited to:

R: This setting can be seen with password no. _ or higher.

W: This setting can be performed with password no. _ or higher (3 is the highest level).

*) In order to change this parameter the regulation must be stopped via the parameter r12 Main switch = OFF.

**) In order to change this parameter the parameter r12 Main switch must be set in position "SEr" allowing manual control of outputs.

10 | AN300028324304en-000401

Wiring diagram pages 2-4

R-W

Code

0-0

r00

1-2

r01

0-2

r02

0-2

r03

1-2

r05

1-2

r09

1-2

r10

0-2

r12

1-2

r13

1-2

r14

1-2

r15

1-2

r16

1-2

r17

0-2

r21

1-2

r61

1-2

r62

1-2

r63

1-2*

r89

1-2

r98

1-2

A03

1-2

A04

1-2

A12

1-2

A13

1-2

A14

1-2

A20

1-2

A21

1-2

A27

1-2

A28

1-2

A36

1-2

c01

1-2

c02

1-2

c05

1-2

c08

Min. value Max. value

1 "r03"

1 0.1 K

1 "r03"

1 -50°C

1 0/°C

1 -10 K

1 -1

1 -50 K

1 1

1 0 %

1 0 hrs

1 0 min.

1 -50°C

1 0 %

1 0 K

1 0 min.

1 0

1 -50°C

1 0 min.

1 -50°C

0 min.

1 0 min.

1 0 %

1 0 min.

1 0 sec

1 1

SW = 2.0x

Factory

Actual

setting

"r02"

20 K

50°C

"r02"

-50

1/F

0/°C

10 K

50 K

100 %

100

10 hrs

30 min.

50°C

100 %

100

50 K

240 min.

240

50°C

-50

240 min.

50°C

-30

50°C

-30

240 min.

100 %

100

30 min.

999 sec