3S SL-R60S 운영 및 유지보수 매뉴얼 - 페이지 4

{카테고리_이름} 3S SL-R60S에 대한 운영 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3S SL-R60S 12 페이지.

페이지 인쇄

Precautions

The Manual is supplied in the language of

the designated country where the product

is used. The translations in various languages

must be authorized by 3S Lift. The operator

must read, understand and follow these

complete product instructions. Failure to do

so may cause severe injury or death. Keep the

product instructions for future references.

1.1

The fall arrester is an integral component

of fall protection system which falls

into category of personal protection

equipment (PPE). Both the fall arrester

and fall protection system we offer

conform to EN353-1:2014+A1: 2017, ANSI/

ASSE Z359.16-2016 and CSA Z259.2.4. The

fall arrester shall be used in conjunction

with a full body harness that is fitted

with a sternal attachment point in

accordance with EN361 and ANSI Z359.11.

1.2

The ladder on which the fall protection

system is mounted should conform

to EN131-2, EN 14122-4, ANSI A14.3 and

withstand the loads specified in the

standards.

1.3

The operator must have obtained a

proper professional training, be familiar

with the operation and installation of

product, and have the ability to attach,

detach and use the product. The

operator must always wear personal

protective equipment, such as safety

helmet, safety shoes and safety gloves,

etc.

1.4

Maximum of 2 operators are allowed on

the same ladder and to attach to the fall

protection system at a time, in which

case a minimum distance of 6 m must

be maintained between them.

The operator may not be protected

1.5

against hitting the ground or the starting

platform within the first 2 m climbing.

Therefore, particular caution must be

taken when operator starts climbing.

1.6 When attaching or detaching the fall

arrester to/from fall protection lifeline,

ensure that the operator is at a safe

position and protected by a separate

personal protection equipment.

1.7 To achieve the optimal operation and

improve safety, keep a minimum

distance of 100mm between torso and

ladder during normal climbing, and

keep correct climbing postures.

1.8 The weight of the operator (including

tools and equipment) shall not exceed

the rated load of 140 kg (310 lbs).

1.9 The weight of the operator (excluding

tools and equipment) shall not be less

than 30 kg (66 lbs).

1.10 The fall arrester shall never be used

for work positioning or for securing

equipment. If work positioning at the

ladder is required, a separate dedicated

and approved work positioning

equipment shall be used.

1.11 A fall arrester can only be used by one

operator at a time.

1.12 Service temperature of fall arrester is

-40°C to +60°C. Ensure that the system is

free of grease oil and ice.

1.13 According to OSHA 1926.1053, the

connection between the fall arrester and

the attachment point of the full body

harness shall not exceed 23 cm (9 inches)

in length! The length of the connection

shall not be extended or shortened, e.g.

by adding or subtracting a connector.

1.14 Always wear a full body harness that

perfectly fits. If it becomes loose during

ascent or descent, adjust it to a snug fit

in time at a safe position.

1.15 The operator must be in good health

without acrophobia, hypertension,

or heart disease, and not be under

influence of alcohol or drugs during

operation.

1.16 If the equipment is found abnormal

during operation, the operator must

immediately stop using it and notify the

equipment administrator.