3Shape TRIOS S3A-14 설정 매뉴얼 - 페이지 4

{카테고리_이름} 3Shape TRIOS S3A-14에 대한 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Shape TRIOS S3A-14 14 페이지.

페이지 인쇄

WARNING

Use of the UNIT adjacent to or stacked with other equip-

ment should be avoided because it could result in improper

operation . If such use is necessary, the UNIT and the other

equipment should be observed to ensure normal operation

in the used configuration .

WARNING

The product needs special precautions regarding electro-

magnetic compatibility (EMC) and needs to be installed and

put into service according to the EMC information provided

in the TRIOS Technical Data .

IMPORTANT NOTICE

The system is to be used in a Professional Healthcare

Environment .

4.2 Intended Use

The 3Shape TRIOS 4 IOS system is intended to obtain 3D digital images

of the topographical characteristics of teeth, including bite, gingivae and

palate directly from the patient's mouth or models of the teeth .

CAUTION

Unintended use of the TRIOS IOS system can result in phys-

ical injury to patients, operators and damage the system .

4.3 Users of TRIOS

The 3Shape TRIOS intraoral scanner system is to be operated by legally quali-

fied healthcare professionals in dental clinics . Using the TRIOS IOS system for

any purpose other than the intended use described above may damage the

TRIOS IOS system and harm operators and patients . Proper use of the TRIOS

IOS system includes following the operation and maintenance instructions,

and observing warnings and caution descriptions in this user guide .

WARNING

Carefully follow the instructions in this guide

If the instructions for operating the TRIOS IOS system

as described in this guide are NOT observed, the intended

protection and safety of the user and patient may be impaired .

4.4 Contra-indications

None

4.5 Patient Target Group

No restrictions in patient population

4.6 System Description

The system is available in these variants:

Regional variation can occur regarding the contents of the systems .

S3P-2

Pen grip scanner, supplied with a pod (holder),

3 scanner batteries, and a scanner battery charger

S3P-8

Pen grip scanner, supplied with a pod (holder)

that is connected to an external PC via an Ethernet cable,

and a TRIOS 4 cord

S3A-10

Pen grip scanner, supplied with a MOVE® cart with built-in PC,

and a TRIOS 4 cord

S3A-14

Pen grip scanner, supplied with a MOVE cart with built-in

PC, 3 scanner batteries, and a scanner battery charger

S3A-18

Pen grip scanner, supplied with a MOVE®+ cart with

built-in PC, and a TRIOS 4 cord

S3A-22

Pen grip scanner, supplied with a MOVE+ cart with built-in

PC, 3 scanner batteries, and a scanner battery charger

You can find the figures in the final section of this guide .

All system variants comprise:

• Handheld TRIOS intraoral scanner, S3-2 (S1 and S2):

Wired and wireless handheld dental intraoral scanner

for scanning the surface of the patient's teeth .

• TRIOS 4 SmartTip, TST-01 (S3): Re-usable scanner tip attached to the

handheld TRIOS Scanner . The scanner tip must be cleaned and sterilized

prior to first use on a patient and after each use on a patient .

The scanner tip as well as the protection tip (S4) can be attached

by the following procedure:

1 . Place the tip over the front tube with the mirror facing upwards

or downwards .

2 . Twist the tip until a firm mechanical click is felt .

3 . The tip is removed doing the opposite procedure:

4 . Twist the tip away from the center of the scanner .

5 . Pull the tip away from the scanner body (S4) .

The label on the protection tip indicates the attaching/removing movement

(S4) . When the tip is detached, the scanner's optical window (S3) is visible .

The TRIOS 4 tip contains a mirror and electronics . A set of scanner tips

is delivered with the scanner . The scanner tip is the only applied part .

• Protection Tip, TST-03 (S4): Protects the optical window of the scanner

from damage and dirt when the scanner is not in use .

• Color Calibration Kit, TST-02 (S5): Used for calibrating TRIOS scanners .

The kit consists of the color calibration target (S6), the sleeve (S7), and

the color calibration adaptor (S8) .

• TRIOS software: Scan application/user interface for the scanner .

• Power (mains) cable and plug: The system is delivered with a cable

appropriate for your location . In the USA and Canada, this is a Nema 5-15P

Hospital Grade mains power cord with plug for the MOVE/MOVE+ cart .

For the charger a C7 connector is used .

• A set of batteries for the scanner, TB-02 or TB-03 (S9)

• A battery charger, C3BP, with wall mount (S10)

For systems S3A-10, S3P-8:

• TRIOS 4 cord, TSC-01 (S11): The wired systems are delivered with a cord,

which is inserted in the scanner by pressing the button as shown in (S2) .

The blue light indicates a connection to either the Pod or the MOVE+ cart .

The green light indicates a connection to the scanner .

System S3A furthermore comprises:

• MOVE cart C 4.0 and MOVE+ cart C 4.1 (Figure 2), for intraoral digital

impression system .

Following description applies to both MOVE and MOVE+ cart:

• Has an adjustable monitor (S12, S13, S14) .

• Has a scanner mount (S15) for holding the scanner while not in use .

• Has wheels for mobility (and brakes (S16) if mobility is not desired) .

• Computer Unit . Attached to the MOVE/MOVE+ cart for processing,

storage and running the TRIOS software .