Casio 1138 운영 매뉴얼

{카테고리_이름} Casio 1138에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 1138 2 페이지.

페이지 인쇄

MO0310-EA

General Guide

• You can use the Remote Control functions while in the Timekeeping Mode.

–

[ Module No. 1173 ]

The operational procedures for Modules 1138 and 1173 are identical. All of

the illustrations in this manual show Module 1138.

Timekeeping Mode

Signal Emitter

Month

Day of week

Date

POWER

TV/VCR

STOP

PLAY

Seconds

Minutes

Hour

PM indicator

About the Timekeeping sub-modes

The Timekeeping Mode is actually made up of three sub-modes. Use the A button

while in the Timekeeping Mode to switch between the sub-modes.

Normal Timekeeping Mode

About the remote control function

In order to be able to use this watch for remote control of a television or video tape

deck, you must first set the appropriate manufacturer code. The manufacturer code

tells the watch what signals to use for remote control. The Manufacturer Code Table

shows the names of the manufacturers that correspond to each code. For full details

on how to actually set the manufacturer code, see "To set the manufacturer code".

Some TV or tape deck models may not work properly with this watch, even

though they are made by one of the manufacturers in the Manufacturer Code

Table. Also, you may find that you can control a TV or tape deck using a code

for a manufacturer that is different from the ones in the table. For details on

finding the code you should use, see "How to find the right code".

Note

• Replacing the battery will cause the remote control data setting (TV/video

manufacturer codes) to be altered. Be sure that you make a note of your codes

before you have the battery replaced.

• There are some manufacturers with more than one code. Try the various codes

available for your equipment to find the one that works best.

• You have to set separate codes for your TV and tape deck, even if they are made by

the same manufacturer.

• You might not be able to use this watch to control models that combine a TV and

tape deck into a single unit, multi-functional TVs that can be used as computer

monitors, or other televisions or tape decks equipped with special functions.

Manufacturer code (TV/Cable Box)

Code

Manufacturer

GOLDSTAR

HITACHI

JERROLD (C)*

JVC

MAGNAVOX

* "(C)" indicates cable box.

Operation Guide 1138 1173

Timekeeping Mode

POWER

TV/VCR

STOP

PLAY

[ Module No. 1138 ]

In addition to normal timekeeping, the Timekeeping

Mode also provides you with remote control capabilities

for your TV* or video tape deck.

* The terms "TV" and "television" as used in this

manual refer to both standard televisions and the

cable box of cable TV systems.

• This watch will control only televisions and video tape

decks that are equipped with remote control sensors.

• For details on how to set the time and date, see "Time

Setting Mode".

Note

The remote control buttons of the watch are marked

according to their functions. In this manual, the buttons

are referred to by using their marking in bold

characters.

Example: Press POWER to switch on the television.

Other (unmarked) buttons are indicated using the

letters A, B, and C, as shown in the illustration.

Press A.

TV Mode

Video Mode

(for television remote

(for video tape deck

control)

remote control)

Manufacturer

Code

Manufacturer

MITSUBISHI

SAMSUNG

MITSUBISHI

SCIENTIFIC ATLANTIC (C)*

MITSUBISHI

SCIENTIFIC ATLANTIC (C)*

PANASONIC

SHARP

PANASONIC

SONY

PANASONIC (C)*

TOSHIBA

PHILIPS

TOSHIBA

PIONEER (C)*

ZENITH

RCA

ZENITH (C)*

RCA

SAMSUNG

• Press C to change from mode to mode. Each mode is explained in detail in the

following sections.

• After you perform an operation in any mode, pressing C returns to the Timekeeping

Mode.

Stopwatch Mode

Manufacturer

GOLDSTAR

HITACHI

JVC

MITSUBISHI

PANASONIC

To set the manufacturer code

TV Mode indicator

Signal Emitter

POWER

TV/VCR

SET

STOP

PLAY

Manufacturer code

6. When you have the correct manufacturer code, press B to return to the

Timekeeping Mode.

• See "To use the remote control functions" for information on using the remote control

functions.

• If you can't find a code that works with your equipment, see "How to find the right

code".

• If you do not press any buttons for a few minutes while the manufacturer code is

flashing, the flashing will stop and the watch automatically returns to the

Timekeeping Mode.

How to find the right code

Use the following operation if you have difficulty finding a manufacturer code that

works with your equipment.

1. Switch on the TV or video tape deck whose manufacturer code you want to set.

2. In the Timekeeping Mode, hold down B until a manufacturer code appears flashing

Code

on the display.

3. Press A to select either the TV Mode (

Mode (

indicator shown on the display).

4. Press

until manufacturer code 01 appears.

• Code 01 comes sequentially after code 39.

• Holding down

increases the code number at high speed.

5. To test whether or not the displayed manufacturer code is correct for your

equipment, point the Signal Emitter (red window) at your TV or tape deck and press

POWER. Note that the TV/tape deck should be switched on.

• If the above operation switches the power of your TV or tape deck off, it means that

the correct code has been selected. Skip to step 6.

• Certain TVs and tape decks may be slow to respond after receiving a remote control

signal. With such units, try holding down POWER for one or two seconds.

• If nothing happens when you press POWER, press

and repeat step 5 to test the code.

• Note that some codes in the Manufacture Code Table do not have manufacturer names.

The watch does not emit remote control signals while these codes are set, and so

you should not use them.

6. After you have found the correct manufacturer code, press B to return to the

Timekeeping Mode.

Alarm Mode

Time Setting Mode

Manufacturer code (video tape deck)

Code

Manufacturer

Code

Manufacturer

PHILIPS

TOSHIBA

PHILIPS

ZENITH

RCA

SAMSUNG

SHARP

SONY

TOSHIBA

1. Switch on the TV or video tape deck whose

manufacturer code you want to set.

2. In the Timekeeping Mode, hold down B until a

manufacturer code appears flashing on the display.

3. Press A to select either the TV Mode (

shown on the display) or Video Mode (

shown on the display).

4. Press

to increase the code number.

• Holding down

increases the code number at high

speed.

• See the Manufacturer Code Table for details on

manufacturer codes.

5. To test whether or not the displayed manufacturer code

is correct for your equipment, point the Signal Emitter

(red window) at your TV or tape deck and press

POWER. Note that the TV/tape deck should be

switched on.

• If the above operation switches the power of your TV or

tape deck off, it means that the correct code has been

selected.

• Certain TVs and tape decks may be slow to respond after

receiving a remote control signal. With such units, try

holding down POWER for one or two seconds.

• If nothing happens when you press POWER, use steps 4

and 5 to try another code.

indicator shown on the display) or Video

to advance to the next code

SET

Code

indicator