Casio 1510 사용자 설명서 - 페이지 6
{카테고리_이름} Casio 1510에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 1510 10 페이지.
페이지 인쇄
To set the current time
1. In the Timekeeping Mode, hold down the
A button for two seconds, until the seconds
A
L
@
digit start to flash on the display.
• The seconds digits are flashing because
M
I
they are selected .
2. Press the J button to display the Home
Time city setting.
E
3. Use K and L to scroll through the available city codes until the one you
want is displayed.
• City codes scroll in the sequence shown in the "CITY CODE TABLE".
4. After setting the Home Time city, use H and J to move the flashing in the
sequence shown below to select other digits and settings.
Press J
Seconds
City Code
Day
Month
• Use the K and L buttons to change the digits when the hour, minutes,
year, month, and day setting are selected (flashing).
• When the 12/24-hour setting is selected, use K to toggle between 12-hour
and 24-hour timekeeping.
5. After the city code, time, and date are set the way you want them, press the
A button to return to the current time display.
Notes
• The year can be set in the range of 1995 to 2039.
• The day of the week is automatically displayed in accordance with the
month and day setting.
• The watch's built-in full automatic calendar automatically make allowances
for different month lengths and leap years. Once you set the date, there
should be no reason to change it except after the replacement of the
watch's battery.
Daylight Saving Time
Use the following procedure to switch between Standard Time and Daylight
Saving Time (summer time). Daylight Saving Time automatically advances
the time setting by one hour from Standard Time.
To switch between Standard Time and Daylight Saving Time
1. In the Timekeeping Mode, hold down the
A
L
A button for two seconds, until the seconds
@
digits start to flash on the display.
2. Press the E button to toggle between
M
I
Standard Time and Daylight Saving Time.
• The indicator DST on the display indicates
that the Home Time is set for Daylight Saving
E
Time.
3. Press the A button to return to the current
time display.
DATA COMMUNICATION
The procedures in this section tell you how to exchange data with a personal
computer running Watch Application, or with another watch.
Important!
See "Data Communication Precautions" for important information about
orienting the watch for data communication and information about
communication errors.
Communicating with a Computer
In this configuration, all of the data selection and settings are performed on
the computer side. Perform the following procedure when the message "Put
the watch in the data transfer mode, and point the two infrared ports towards
each other." appears on the computer.
To communicate with a computer
1. Press the I button.
Infared port
PC
2.
press the E button to enter the PC
Communication Mode.
A
L
@
3. Align infrared ports of the watch and
computer, and click
dialog box on the computer's screen.
M
I
• The watch establishes an infrared link with
the computer and data transfer starts.
E
4. After data communication is complete, the message
watch display, and then the watch changes to the Timekeeping Mode.
Interrupting Data Communication
Press the I button to interrupt a data communication operation.
• Communication stops and the message
appears on the display. Press the I button again to return to the
Timekeeping Mode.
Press H
Hour
Minutes
12/24-Hour
Year
Format
is flashing on the operation menu, so
OK
on the message
OK!
appears on the
TRANSFER
ERROR!
Owner Data Exchange
With the following operation, the two watches exchange the data in their
respective Owner Modes. Received data is stored as a Telememo Mode record.
To exchange Owner data
1. On both watches, press the I button.
2. Press L to move the flashing to
• Note that the
WATCH
item is not shown if the watch does not have any
data input in its Owner Mode.
AUTO
is flashing on the operation menu, so press the E button.
3.
4. Align infrared ports of the two watches.
• The watches establish an infrared link with each other and data transfer starts.
5. After data communication is complete, the message
watch display, and then the watches change to the Telememo Mode,
showing the received data.
Communicating with Another Watch
Use the following procedures to exchange Telememo, Schedule, To Do, and
Browser data with another watch. In this configuration, one watch is the
sender and the other watch is the receiver.
To send data to another watch (sender operation)
1. Enter the mode that contains the data you want to send, and display the
data.
• If you display a Telememo Mode index name, all of the records under the
index are sent to the other watch.
• When you send Browser data, all of the lines in the displayed page are sent.
2. Press the I button.
3. Press L to move the flashing to
and then press the E button.
SEND
A
L
4.
@
so press the E button.
5. Press the E button to start the data send
M
I
operation.
• If you displayed a Telememo index name in
step 1, the above screen shows
E
instead of
• If you displayed Browser data in step 1, the
A
L
above screen shows
@
ONE
6. Align infrared ports of the two watches.
M
I
• The watches establish an infrared link with
each other and data transfer starts.
E
7. After data communication is complete, the message
watch display, and then the watch changes to the screen that shows the
data that was sent.
To receive data from another watch (receiver operation)
1. Enter the mode for the data you will be receiving.
• To receive Owner Mode data, enter the Owner Mode.
2. Press the I button.
3. Press L to move the flashing to
4. Press L to move the flashing to
5. Press the E button to start the data receive operation.
6. Align infrared ports of the two watches.
• The watches establish an infrared link with each other and data transfer
starts.
7. After data communication is complete, the message
watch display, and then the watch changes to the screen that shows the
data that was received.
REFERENCE
This section contains more detailed and technical information about watch
operations.
Button Input Confirmation Tone
Use the following procedure to turn the button input confirmation tone on and off.
To turn the button input confirmation tone on and off
1. In the Timekeeping Mode, press the M
A
L
button three times to display Menu Screen
@
3.
2. Press the L button to move the flashing to
M
I
OPTION
3. The sound setting is flashing on the display,
so press H or J to execute the displayed
E
setting.
• If the button confirmation tone is currently turned on, the display shows
SOUND ON
. If the tone is currently off, the display shows
4. After you are finished making the setting you want, press the M button to
return to the Timekeeping Mode.
1510-6
WATCH
, and then press the E button.
OK!
appears on the
WATCH
is flashing on the operation menu,
INDEX
ONE
.
PAGE
instead of
.
OK!
appears on the
WATCH
, and then press the E button.
RECEIVE
.
OK!
appears on the
, and then press E.
SOUNDOFF
,
.