Casio 1699 사용자 설명서

{카테고리_이름} Casio 1699에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 1699 2 페이지.

페이지 인쇄

2-2. QW-1699

• Press M to change from mode to mode.

Timekeeping Mode

TIMEKEEPING MODE

To set the time and date

1. Hold down A while in the Timekeeping Mode until the

Day of week

Month – Day

seconds digits start to flash on the display. The seconds

flash because they are selected .

2. Press M to change the selection in the following

sequence.

Seconds

Hour : Minutes

PM indicator

Seconds

Day

Month

3. While the seconds digits are selected (flashing), press C to reset the seconds to

• If you press C while the seconds count is in the range of 30 to 59, the seconds are

reset to

and 1 is added to the minutes. If the seconds count is in the range of 00 to

29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press C to increase

the number. While the 12/24-hour setting is selected, press C to switch between the

two formats.

• Holding down C changes the current selection at high speed.

• When the 12-hour format is selected, the

the 12-hour format, the P (PM) indicator appears on the display to indicate "p.m."

times. There is no indicator for "a.m." times.

• Selecting the 24-hour format causes the

display.

5. After you set the time and date, press A to return to the Timekeeping Mode.

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

BACKLIGHT FUNCTION

A backlight that uses an EL (electro-lumunescent) panel

Auto light switch on indicator

causes the entire display to glow for easy reading in the

dark. An auto light switch causes the EL backlight to turn on

when the watch is angled toward your face for reading. An

EL alarm feature can be turned on so the backlight flashes

whenever an alarm or hourly time signal sounds.

• The auto light switch on indicator is shown on the display

in all modes while the auto light switch is on.

• The FLASH indicator is shown on the display in all modes

while the EL alarm is on.

Note

• The backlight of the watch employs an electro-luminescent

FLASH indicator

(EL) light, which loses illuminating power after very long

use.

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. This is caused

by a transistor that vibrates when the EL panel lights up. It does not indicate malfunction

of the watch.

• The backlight automatically turns off whenever an alarm sounds.

To manually turn on the backlight

Pressing L in the Timekeeping, Stopwatch or Alarm Mode causes the backlight to turn

on for about two seconds. Pressing C in the Beat Counter Mode also causes the backlight

to turn on for a fixed amount of time.

• The backlight normally stays on for about two seconds and then turns off automatically.

When the EL alarm is turned on, however, the backlight stays on for about five seconds

instead of two seconds.

• The above operations turn on the backlight, regardless of the current auto light switch

and EL alarm settings.

Beat Counter Mode

Hour

Minutes

12/24-Hour

Year

Format

indicator appears on the display. With

12H

and the 24 indicators to appear on the

24H

GENERAL GUIDE

Stopwatch Mode

To turn the EL alarm on and off

In the Timekeeping Mode, hold down B for about two seconds to toggle the EL alarm

on (FLASH indicator displayed) and off (FLASH indicator not displayed).

• When the EL alarm is on, the backlight flashes while the daily alarm and hourly time

signal tones are sounding. Also, the backlight stays on for about five seconds instead

of the normal two seconds.

• When an auto light switch operation causes the backlight to turn on while the EL alarm

is turned on, the backlight stays lit for about two seconds, and then flashes for two

seconds.

About the Auto Light Switch

While the auto light switch is turned on, the backlight automatically lights for about two

seconds whenever you position your wrist as described below. Avoid wearing the watch

on the inside of your wrist. Doing so causes the auto light switch to operate when it is not

needed, which shortens battery life.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes the backlight to illuminate.

• The backlight may not illuminate if the face of the watch is more than 15 degrees off

the parallel as shown below. Make sure that the back of your hand is parallel to the

ground.

Parallel to ground

• Static electricity or magnetic force can interfere with proper operation of the auto light

switch. If the auto light switch does not illuminate, try moving the watch back to the

starting position (parallel with the ground) and then tilt it back toward you again. If this

does not work, drop your arm all the way down so it hangs at your side, and then bring

it back up again.

• Under certain conditions the backlight may not light until about one second or less

after turn the face of the watch towards you. This does not necessarily indicate

malfunction of the backlight.

Warning!

• Never try to read your watch when mountain climbing or hiking in areas that are

dark or in areas with poor footing. Doing so is dangerous and can result in

serious personal injury.

• Never try to read your watch when running where there is danger of accidents,

especially in locations where there might be vehicular or pedestrian traffic. Doing

so is dangerous and can result in serious personal injury.

• Never try to read your watch when riding on a bicycle or when operating a

motorcycle or any other motor cycle. Doing so is dangerous and can result in a

traffic accident and serious personal injury.

• When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor vehicle.

Sudden and unintended operation of the auto light switch can create a distraction,

which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down C for one second to turn the auto light switch on

(

displayed) and off (

• In order to protect against running down the battery, the auto light switch is automatically

turned off approximately three hours after you turn it on. Repeat the above procedure

to turn the auto light switch back on if you want.

— 9 —

Alarm Mode

Parallel to

ground

More than 15 degrees

too high

too low

not displayed).

More than

40 °