Casio 1760 일반 매뉴얼

{카테고리_이름} Casio 1760에 대한 일반 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 1760 2 페이지.

Module No.1760

The figures on the display of your watch may be black-on-white or white-on-black, depending on the model. Operations are the same regardless of the display type.

• Press C C C C C to change from mode to mode.

• In any mode (except when making any settings), press B B B B B to illuminate the display for about four seconds.

Home Time Display

TIMEKEEPING MODE

Home Time Display

Day of week

indicator

Seconds

Hour

Minutes

Home Time and Dual Time

Home Time shows the current time in the area you normally live, while Dual Time

shows the current time in another time zone. You can switch the digital display be-

tween Home Time and Dual Time without changing the analog (hands) setting, or

you can make the current Dual Time setting your Home Time setting (which also

changes the analog setting).

Switching the Digital Time Display Between the Home Time and Dual Time

Press D D D D D to toggle the digital time display between Home Time and Dual Time. The

analog setting does not change.

• The indicator "

" in the upper part of the display indicates Dual Time is select-

ed. The indicator "

" appears after you select Home Time, but after about one

second it is replaced by the current day of the week and day of the month.

Making the Dual Time Setting Your Home Time Setting

• Hold down D D D D D for about two or three seconds to change the Dual Time setting to

your Home Time setting. The previous Home Time setting becomes the new Dual

Time setting.

• This operation also changes the analog setting so it matches the new Home Time.

Important!

The alarm sounds when the Home Time matches the currently set alarm time, re-

gardless of whether Home Time or Dual Time is selected.

To set the Home Time and date

1. Hold down A A A A A while the Home Time is displayed in the Timekeeping Mode until the

second digits flashes on the display because they are selected .

2. Press C C C C C to change the selection (flashing) in the following sequence.

Seconds

Hour

Day

Month

3. While the seconds setting is selected (flashing), press D D D D D to reset it to 00. If you

press D D D D D while the seconds setting is in the range of 30 to 59, the seconds are reset

to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00 to

29, the minutes count is unchanged.

• While any other setting (besides seconds) is selected (flashing), press D D D D D to in-

crease it or B B B B B to decrease it.

• While the 12/24-hour format setting is selected, press D D D D D to toggle it between 12

and 24.

• Except for when adjusting the seconds or setting the 12/24-hour format, holding

down a button changes the current selection at high speed.

• When the 12-hour format is selected, the indicator P appears on the display to

indicate "P.M." times. There is no indicator for "A.M." times.

4. After you set the time and date, press A A A A A to return to the Timekeeping Mode Home

Time display.

• This operation also changes the analog setting so it matches the new Home Time.

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a setting is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode Home Time dis-

play automatically.

To set the Dual Time

1. Hold down A A A A A while the Dual Time is displayed in the Timekeeping Mode, until the

hour digits flashes on the display because they are selected .

2. Press C C C C C to change the selection (flashing) in the following sequence.

Hour

3. While any setting is selected (flashing), press D D D D D to increase it or B B B B B to decrease it.

• Holding down a button changes the current selection at high speed.

4. After you set the dual time, press A A A A A to return to the Timekeeping Mode Dual Time

display.

Timeekeeping Mode

Dual Time Display

Press D D D D D

Dual Time Display

Day

PM indicator

Press D D D D D

Hour

Minutes

12/24-Hour

Format

Year

Minutes

GENERAL GUIDE

File Mode

Press C C C C C

Synchro Mode

• The second count of the Dual Time is synchronized with the second count in the

Home Time.

• If you do not operate any button for a few minutes while a setting is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode Dual Time dis-

play automatically.

• The format (12-hour and 24-hour) of the dual time matches the format you select

for Home Time.

About the Backlight

In any mode (except when making settings) press B B B B B to illuminate the digital display

for about four seconds.

• The backlight automatically turns off whenever an alarm sounds.

• The backlight of the watch employs an electro-luminescent (EL) panel, which loses

Seconds

illuminating power after very long use.

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. This is

caused by a transistor that vibrates while the EL panel is lit. It does not indicate

malfunction of the watch.

Name area

Mode indicator

Telephone number area

To input new File data

Remaining memory

2. Hold down A A A A A while the capacity display is on the screen and a cursor appears in

the name area.

3. Use D D D D D or B B B B B to input a character at the cursor position. The character changes in

the following sequence. Holding down either button changes the character at high

speed.

Press

4. After you select the character you want, press C C C C C to advance the cursor to the right.

• Repeat 3 and 4 until you complete name input.

• You can input up to 4 characters in the name area.

5. After the name input is through, use C C C C C to move the cursor to the telephone number

area.

6. While the cursor is in the telephone number area, use D D D D D or B B B B B to input a number

you want. The character changes in the following sequence. Holding down either

button changes the character at high speed.

Press

7. After you select the character you want, press C C C C C to advance the cursor to the right.

• Repeat 6 and 7 until you complete number input.

• You can input up to 12 characters in the telephone number area.

8. After inputting your data, press A A A A A to store it and return to the File Mode.

• When you press A A A A A to store data, the message "

a few seconds. After the sort operation is complete, the normal File Mode display

(without the cursor) appears.

• The number area of the display can show only six digits at a time, so longer num-

bers scroll continuously from right to left.

• Inputting hyphens into your phone numbers make them easier to read when you

recall them.

Alarm Mode

Stopwatch Mode

FILE MODE

The File Mode lets you store up to 20 pages of name and

telephone number data. You can recall data by scrolling

through it on the display.

• You can input up to four characters in the text area, and

12 digits in number areas.

• The data item on the display when you exit the File Mode

appears first the next time you enter the File Mode.

1. In the File Mode, press D D D D D until the capacity display ap-

pears.

• Holding down D D D D D and pressing B B B B B scrolls through data in

reverse sequence.

• If there is no File data stored in memory yet, the capac-

ity display appears as soon as you enter the File Mode.

• If the message "

" appears on the display, it means

that memory is full. To store more data, you will first

have to delete some of the data.

(Space)

(Hyphen)

" appears on the display for

1760-1

(Hyphen)

(Space)