Casio 2165 일반 매뉴얼

{카테고리_이름} Casio 2165에 대한 일반 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2165 2 페이지. Module

Module No. 2165

• If the contents of the display seem to be continually changing, see "AUTO DISPLAY FUNCTION" for information on how to stop it.

• Press C C C C C to change from mode to mode.

• In any mode, press L L L L L to illuminate the display for about 3 seconds.

Timekeeping Mode

Day of The

Week Display

Press B B B B B .

TIMEKEEPING MODE

• In the Timekeeping Mode, press D D D D D to switch between

Month - Day

Day of week

• Press L L L L L in the Timekeeping Mode to activate the EL

• The Timekeeping Mode has two displays. One shows

FRI

• There are three different time graph formats, which

Hour

Seconds

Minutes

PM indicator

No Alarm Time Setting for Current Date

Month - Day

Time graph

Alarm Time Setting for Current Date

Appointment icon

An appointment icon appears on the display and the time

graph hour for which the alarm is set flashes. The time

Time graph

graph shows how long before the alarm time will be

Appointment

reached.

time indicator

Month - Day

Alarm Time Setting Within the Hour

Appointment icon

One hour before an alarm time is reached, a tone sounds

and the time graph format changes, replacing the month

Time graph

and day with a countdown of the minutes and seconds

Appointment

left until the alarm time is reached.

time indicator

Remaining minutes and seconds

To set the time and date

1. Hold down A A A A A while in the Timekeeping Mode. The seconds digits flash on the

display because they are selected .

2. Press C C C C C to change the selection in the following sequence.

Seconds

Animated Graphic

3. While the seconds digits are selected (flashing), press D D D D D to reset the seconds to

00. If you press D D D D D while the seconds count is in the range of 30 to 59, the seconds

are reset to 00 and 1 is added to the minutes. If the seconds count is in the range

of 00 to 29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press D D D D D to in-

crease the number or B B B B B to decrease it. Holding down either button changes the

current selection at high speed.

• While the animated graphic is flashing, you can select one of the following graph-

ics. The animated graphic you select appears on the display whenever you turn on

the EL backlight in the Timekeeping Mode.

1. Random selection of 2, 3, or 4.

2. LOVERS A

3. LOVERS B

4. LOVERS C

Telememo Mode

Time Graph

Display

the 12-hour and 24-hour formats.

backlight and to display animated graphics.

the

Mark along with the current day of the week. The

other display shows a time graph for the current date.

Pressing B B B B B switches between the two displays.

change automatically in accordance with the current re-

lationship between an alarm time setting and the cur-

rent time.

Hour

Minutes

Year

Month

Day

GENERAL GUIDE

Alarm Mode

5. After you set the time and date, press A A A A A to return to the Timekeeping Mode.

• The day of week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

About the backlight

In any mode, press L L L L L to illuminate the display for about 3 seconds.

• The backlight of the watch employs an electro-luminescent (EL) light, which loses

illuminating power after very long use.

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. This is

caused by a transistor that vibrates when the EL panel lights up. It does not indi-

cate malfunction of the watch.

• The backlight automatically turns off whenever an alarm sounds.

The following causes all data stored in memory to be deleted. Be sure to

always keep separate written copies of all important data.

Malfunction or repairs/Dead battery/Battery replacement

In no event will CASIO be liable for loss of data or any damages arising out of

such loss.

Mode indicator

Remaining

memory

Name

Telephone

number

[New Data Display]

Text area

Number area

3. Use D D D D D or B B B B B to input a character at the cursor position. The character changes in

the following sequence. Holding down either button changes the character at high

speed.

Press

(Space)

Press

4. After you select the character you want, press C C C C C to advance the cursor to the right.

• Repeat 3 and 4 until you complete name input.

• You can input up to 8 characters in the name area.

5. After the name input is through, use C C C C C to move the cursor to the telephone number

area.

6. While the cursor is in the telephone number area, use B B B B B or D D D D D to input a number

you want. The character changes in the following sequence. Holding down either

button changes the character at high speed.

Press

7. After you select the character you want, press C C C C C to advance the cursor to the right.

• Repeat 6 and 7 until you complete number input.

8. After you input the telephone number you want, use C C C C C to move the cursor to the

cell phone number area.

• The

indicator indicates the cell phone display.

• Input the cell phone number using the same procedure as you did for the telephone

number.

• If you don't want to input a cell phone number, proceed from step 9 without input-

ting anything.

Stopwatch Mode

TELEMEMO MODE

Caution

The Telememo Mode lets you store up to

20 pages of name, telephone number, and

cell phone (or pager) number data. You can

recall data by scrolling through it on the dis-

play.

• The number of unused pages still availa-

ble for storage of data appears on the dis-

play every time you enter the Telememo

Mode.

• You can input up to eight characters in

the text area, and 12 digits in each of the

two (telephone and cell phone) number

areas.

• The data item on the display when you

exit the Telememo Mode appears first the

next time you enter the Telememo Mode.

To input new Telememo data

1. In the Telememo Mode, press D D D D D or B B B B B until the New

data display appears.

• The new data display is the one that is blank (contains

no name and telephone number).

• If there is no Telememo data stored in memory yet, the

new data display appears as soon as you enter the Tele-

memo Mode.

• If the message "

" appears on the display, it

means that memory is full. To store more data, you will

first have to delete some of the data.

2. Hold down A A A A A and a cursor appears in the text area.

A to Z

0 to 9

– (Hyphen)

0 to 9

2165-1

(Space)