Casio 2198 일반 매뉴얼 - 페이지 2

{카테고리_이름} Casio 2198에 대한 일반 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2198 9 페이지.

페이지 인쇄

• The backlight turns off in about two seconds, even if you keep the watch

pointed towards your face.

• Static electricity or magnetic force can interfere with proper operation of the

auto light switch. If the backlight does not illuminate, try moving the watch

back to the starting position (parallel with the ground) and then tilt it back

toward you again. If this does not work, drop your arm all the way down so

it hangs at your side, and then bring it back up again.

• Under certain conditions the backlight may not light until about one second

or less after turn the face of the watch towards you. This does not necessarily

indicate malfunction of the backlight.

Warning!

• Never try to read your watch when mountain climbing or hiking in

areas that are dark or in areas with poor footing. Doing so is dangerous

and can result in serious personal injury.

• Never try to read your watch when running where there is the danger

of accidents, especially in locations where there might be vehicular or

pedestrian traffic. Doing so is dangerous and can result in serious

personal injury.

• Never try to read your watch when riding on a bicycle or when

operating a motorcycle or any other motor vehicle. Doing so is

dangerous and can result in a traffic accident and serious personal

injury.

• When you are wearing the watch, make sure that its auto light switch

is turned off before riding on a bicycle or operating a motorcycle or

any other motor vehicle. Sudden and unintended operation of the auto

light switch can create a distraction, which can result in a traffic

accident and serious personal injury.

TIMEKEEPING FUNCTIONS

Day of week

You can set the time and date in the

Month – Day

Timekeeping Mode, which you can enter

Graphic display

using C.

• In the Timekeeping Mode, the graphic

display shows counting of the seconds.

To set the time and date

1. In the Timekeeping Mode, press D until

Year

A S

2. Hold down A until the seconds digits start

Hour

Seconds

Minutes

PM indicator

3. Press C to change the selection in the following sequence.

Seconds

Hour

Day

4. While the seconds digits are selected (flashing), press D to reset the

seconds to "00". If you press D while the seconds count is in the range of 30

to 59, it is reset to "00" and 1 is added to the minutes. If the seconds count is

in the range of 00 to 29, the minutes count is unchanged.

5. While any other digits (besides seconds) are selected (flashing), press D

to increase the number or B to decrease it. Holding down either button

changes the current selection at high speed.

While the 12/24-hour setting is selected, press B or D to switch between

the two formats.

6. After you set the time and date, press A to return to the Timekeeping

Mode (Timekeeping screen).

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping

Mode automatically.

DIGITAL COMPASS FUNCTIONS

This watch features a built-in bearing sensor that indicates any one of 16

directions. Up to five sets of direction readings can be stored into memory.

Each set of data includes the direction, along with the date and time of the

measurement. Direction readings can be performed in the Digital Compass

Mode.

the Timekeeping screen appears.

to flash on the display. The seconds digits

flash because they are selected .

12/24-Hour

Minutes

Format

Month

Year

To enter and exit the Digital Compass Mode

1. In any mode (except for the Alarm Mode), press E to enter the Digital

Compass Mode.

• At this time, the watch immediately starts a Digital Compass operation.

After about one second, the direction that the 12 o'clock position of the

watch is pointing appears on the display.

• If you do not perform any button operation for a few minutes, the watch

automatically returns to the mode you were in before entering the Digital

Compass Mode.

2. Press C to return to the mode you were in before entering the Digital

Compass Mode.

• Note that when you enter the Digital Compass Mode from the Altimeter

Mode, the Altimeter Mode measurement (see "About altitude

measurements") continues to be performed internally.

To take a direction reading without storing data into

memory

1. Place the watch on a flat surface or (if you

Magnetic north indicator

Date

Direction

• Note that taking a measurement while the

watch is not horizontal (in relation to the

horizon) can result in large measurement

error.

2. Point the 12 o'clock position of the watch

3. Press E to enter the Digital Compass

BEARING

A S

• After about one second, the direction that

the 12 o'clock position of the watch is

Mode indicator

Time

pointing appears on the display.

• Also, four indicators appear to indicate

Direction value (in degrees)

magnetic north, south, east, and west.

• The direction value that appears on the

Magnetic north

display represents the clockwise angle

formed between magnetic north (which is 0

degrees) and the displayed direction.

Displayed

• You can repeat steps 1 through 3 as many

direction

times as you like.

Direction

• The following table shows the meanings of

value

each of the direction abbreviations that

appear on the display.

Direction

Meaning

Direction

North

SSW

WNW

East

South

West

North-

NNE

northeast

East-

ESE

southeast

4. Next, you can adjust the rotary direction

• The Digital Compass operation is

automatically interrupted whenever an

alarm (Daily Alarm or Hourly Time Signal)

sounds. If this happens, start the Digital

BEARING

A S

Compass operation again from the

beginning.

To take a direction reading and store data into memory

1. While in the Digital Compass Mode, use

BEARING

A S

Memory number

(memory area screen only)

1998/2198-2

are wearing the watch), make sure that

your wrist is horizontal (in relation to the

horizon).

in the direction you want to measure.

Mode and to start a Digital Compass

measurement operation.

Meaning

Direction

Meaning

South-

East-

ENE

southwest

northeast

South-

West-

SSE

northwest

southeast

West-

Northeast

WSW

southwest

North-

Southeast

NNW

northwest

Southwest

Northwest

bezel so that the "N" or "

" mark is aligned

with the magnetic north indicator. This

correctly aligns all of the markings on the

bezel.

D to select the memory area where you

want to store the data. Each time you

press D, the selected memory area

changes in the following sequence.

Normal

Memory 1

Memory 2

Screen

Memory 5

Memory 4

Memory 3