Casio 2345 일반 매뉴얼 - 페이지 2
{카테고리_이름} Casio 2345에 대한 일반 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2345 6 페이지. Watch
페이지 인쇄
ABOUT THE BACKLIGHT
This watch features an electroluminescent (EL) backlight that helps you easily
read the face, even in total darkness. Its auto light switch automatically lights
the watch face whenever you turn your wrist towards your face.
A
B
• The backlight of Module 2347 illuminates
both the digital display and analog face. The
backlight of Module 2345 illuminates the
digital display only.
C
D
Note
• The backlight of the watch employs an electroluminescent (EL) light, which
loses illuminating power after very long use.
• Frequent use of the backlight shortens the battery life.
• The illumination provided by the backlight may be hard to see when viewed
under direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. It
does not indicate malfunction of the watch.
• The backlight automatically turns off whenever an alarm sounds.
To manually turn on the backlight
• Pressing B in any mode besides the Countdown Alarm Mode or
Stopwatch Mode illuminates the display for about 1.5 second. The backlight
is disabled while a setting screen is on the display.
To switch the auto light switch on and off
While in the Timekeeping Mode, hold down D for one second to turn the auto
light switch on and off.
Hold down D.
C
D
Auto light switch
on indicator
ON
• Note that pressing D also changes the display.
• The auto light switch on indicator is shown on the display in all modes while
the auto light switch is on.
• In order to protect against running down the battery, the auto light switch is
automatically turned off approximately six hours after you turn it on. Repeat
the above procedure to turn the auto light switch back on if you want.
• Pressing B in any mode besides the Countdown Alarm Mode or
Stopwatch Mode illuminates the display for about 1.5 second, regardless of
the auto light switch on/off setting.
About the auto light switch
While the auto light switch is turned on, the backlight automatically lights for
about 1.5 second in any mode whenever you position your wrist as described
below.
Important!
Avoid wearing the watch on the inside of your wrist. Doing so causes the auto
light switch to operate when it is not needed, which shortens battery life.
Moving the watch to a position that is parallel to the ground and then tilting
it towards you more than 40 degrees causes the backlight to illuminate.
Parallel to
ground
• The backlight may not illuminate if the face of the watch is more than 15
degrees off parallel as shown below. Make sure that the back of your hand
is parallel to the ground.
Parallel to ground
More than 15 degrees
too high
C
D
OFF
More than
40°
More than 15 degrees
too low
• Static electricity or magnetic force can interfere with proper operation of the
auto light switch. If the backlight does not illuminate, try moving the watch
back to the starting position (parallel with the ground) and then tilt it back
towards you again. If this does not work, drop your arm all the way down so
it hangs at your side, and then bring it back up again.
• Under certain conditions the backlight may not light until about one second
or less after turn the face of the watch towards you. This does not
necessarily indicate malfunction of the backlight.
Warning!
• Never try to read your watch when mountain climbing or hiking in
areas that are dark or in areas with poor footing. Doing so is
dangerous and can result in serious personal injury.
• Never try to read your watch when running where there is the danger
of accidents, especially in locations where there might be vehicular or
pedestrian traffic. Doing so is dangerous and can result in serious
personal injury.
• Never try to read your watch when riding on a bicycle or when
operating a motorcycle or any other motor vehicle. Doing so is
dangerous and can result in a traffic accident and serious personal
injury.
• When you are wearing the watch, make sure that its auto light switch
is turned off before riding on a bicycle or operating a motorcycle or
any other motor vehicle. Sudden and unintended operation of the
backlight can create a distraction, which can result in a traffic
accident and serious personal injury.
BAROMETER MODE
This watch uses a pressure sensor to measure barometric pressure. It can be
adjusted to correct for measurement error.
Important !
The barometer that is built into this watch measures changes in barometric
pressure, which you can then apply to your own weather predictions. It is not
intended for use as a precision instrument in official weather prediction or
reporting applications.
Example barometer applications
• Before going mountain climbing, you can take readings to predict upcoming
weather.
• You can predict the weather for golf or other outdoor activities.
About barometric pressure measurements
The watch takes barometric pressure measurements every five seconds for
the first two minutes after you enter the Barometer Mode. The Barometer
Mode indicator 1 flashes on the display during these two minutes.
After the first two minutes, the Barometer Mode indicator 1 stops flashing, and
the watch automatically takes measurements every two hours (starting from
midnight).
The watch continues to take barometric pressure readings every two hours,
even if you change to another mode. Measurement data can be viewed on the
Timekeeping Mode screen on the barometric pressure graph.
Barometer Mode
5 seconds
indicator 1
A
B
later
C
D
Remaining memory
Barometer Mode indicator 2
*1 The barometric pressure graph shows the barometric pressure readings
for the past 18 hours. The flashing point on the right of the display is the
point of the last measurement.
*2 The displays show "– – – – hPa" (or inHg) if a measured value falls outside
the range of 460 hPa/mb to 1100 hPa/mb (13.55 inHg to 32.45 inHg). The
normal display will return as soon as the pressure returns with the
allowable range.
2345/2347-2
Last measurement *
2
(updated every two hours)
Unit of measurement
Press A.
M
Barometric pressure graph *
1