Danfoss 088L5130 사용자 설명서 - 페이지 5

{카테고리_이름} Danfoss 088L5130에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Danfoss 088L5130 6 페이지.
Danfoss 088L5130에 대해서도 마찬가지입니다: 사용자 설명서 (20 페이지), 설치 매뉴얼 (4 페이지)

페이지 인쇄

Programmable Thermostats 088L5130/5132

Please note: Usually, the electrician who installed the thermostat

will have set the correct time and day of the week.

Factory setting: Mon

DAY

SETTINGS

MON

FRI

Read Out

I want to know the amount of time (in percent) that

the heating has been turned on within a certain

period.

To do so, you must:

Press the OK button twice to activate the menu.

Press the Up or Down buttons until the Settings option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the Readout option ﬂ ashes.

Press the Up or Down buttons to the select the period of inter-

est: 2 days, 30 days or 365 days. The percentage of time that

the heating has been turned on will then be indicated in the

upper part of the display.

The Readout submenu also contains information about the

Software version and the type of control (Room, Floor, Regu-

lator or Room limit) selected for the Application.

(See Application for more information).

SETTINGS

READOUT

Offset Temperature

I want to adjust the difference in temperature

between the thermostat and my room thermometer.

To do so, you must:

Press the OK button twice to activate the menu.

Press the Up or Down buttons until the Settings option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the Offset Temp option

ﬂ ashes.

Press the Up or Down buttons to set the offset temperature (in

steps of 1°).

Press the OK button.

Select Exit to exit the option.

Offset is used to compensate for any difference between the

thermostat and a room thermometer. It is possible to adjust the

offset by up to +/- 10°C or +/- 18°F. Once the offset has been set

correctly, the thermostat will display the same temperature as the

thermometer.

TUE

WED

THU

SAT

SUN

2 DAYS

30 DAYS

365 DAYS

SOFTWARE

APPLICATION

EXIT

If, for example, the thermostat shows 1° too much, the offset

should be set to 1°. The temperature will then be set 1° lower.

SETTINGS

OFFSET TEMP

Application

I want to select the type of temperature control.

To do so, you must:

Press the OK button twice to activate the menu.

Press the Up or Down buttons until the Settings option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the Application option

ﬂ ashes.

Press the Up or Down buttons to select one of the four types

of control:

Room: The air sensor is used. Only room temperature is

controlled.

Floor: A ﬂ oor sensor is used. Only ﬂ oor temperature is control-

led. (Factory default for 088L5132)

Regulator: The thermostat functions as a simple regulator and

no sensors are used.

Room limit: The thermostat controls room temperature while

using the ﬂ oor sensor as a limit sensor. If you choose this op-

tion, you must set a maximum and minimum temperature for

the limit sensor, so that the thermostat will switch the heating

off or on if the temperature on the ﬂ oor reaches the maximum

or minimum temperature respectively. This can, for instance,

be used to avoid excessively high temperatures on wooden

ﬂ ooring (maximum limit) or excessively cold temperatures

on tiled/stone ﬂ ooring (minimum limit). (Factory default for

088L5132)

Press the OK button.

Select Exit to exit the option.

Please note: Usually, the electrician who installed the thermostat

will have selected the correct type of temperature control for your

application.

ROOM

FLOOR

REGULATOR

ROOM LIMIT

TIME

DAY

CHILDLOCK

SETTINGS

C°/F°

APPLICATION

OFFSET TEMP

READOUT

ADAPTIVE

DISPLAY

FACTORY RESET

EXIT

English