Casio 2535 사용자 설명서

{카테고리_이름} Casio 2535에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2535 5 페이지.

페이지 인쇄
Casio 2535 사용자 설명서
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
Be sure to read "Battery" of this manual for important
information you need to know when exposing the watch to bright light.
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watch's Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and puts
the watch into a sleep state whenever your watch is left
for a certain period where it is dark.
The initial factory default setting is Power Saving on.
The watch recovers from the sleep state if you move it to
a well-lit area
the watch towards your face for reading.
It can take up to five seconds for the display to turn on.
*
See "Power Saving Function" for more information.

General Guide

Press C to change from mode to mode.
In any mode, press L to illuminate the display.
Timekeeping Mode

Timekeeping

Use the Timekeeping Mode to set and view the current
Hour : Minutes Seconds
time and date.
Year
To set the time and date
1. In the Timekeeping Mode, hold down B until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds
Day of week
Month – Day
Power Saving
PM indicator
3. When the setting you want to change is flashing, use D and A to change it as
described below.
Setting
Screen
Press D to reset to 00.
Seconds
Use D (+) and A (–) to change the setting.
Hour, Minutes
Press D to toggle between 12-hour (12H) and
12/24-Hour
Format
24-hour (24H) timekeeping.
Use D (+) and A (–) to change the setting.
Year, Month, Day
Press D to toggle Power Saving on (ON) and
Power Saving
off (OFF).
4. Press B to exit the setting screen.
See "Power Saving Function" for details about configuring Power Saving settings.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.

Stopwatch

The 1/100-second stopwatch can measure elapsed time
Remaining memory
and lap/split times. The stopwatch uses the basic data you
Minutes
input and a pacer signal to calculate the distance you
Seconds
Hours
cover while jogging or running. Stopwatch times and your
distance are also stored in memory.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a lap/split time is
frozen on the display clears the lap/split time and returns
to elapsed time measurement.
Stopwatch measurements are performed in the
Stopwatch Mode, which you enter by pressing C.
Timekeeping
Mode time
1/100 second
USER'S GUIDE 2535
, if you press any button, or if you angle
*
Press C.
12/24-Hour
Hour
Minutes
Format
Day
Month
Year
Button Operation
About This Manual
Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
(Light)
Stopwatch Mode
Alam Mode
How the Stopwatch Works
There are two ways you can use the stopwatch: to measure elapsed time and lap/split
times like a standard stopwatch (see "To measure times with the stopwatch"), and to
keep track of the distance you cover while jogging or running. In order to use the
stopwatch to keep track of distance, you must first perform the steps listed below.
1. Set your basic data. See "Basic Data".
2. Turn on the pacer signal. See "To turn the pacer signal on and off".
Note
In order to obtain accurate distance calculations, you must set accurate basic data
and keep your exercise pace in accordance with the pacer signal emitted by the
watch.
See "How Stopwatch Data is Stored" for information about the type of data the watch
stores in memory when you use the stopwatch.
Use the Recall Mode to view data stored in memory.
You can view distance covered data only by recalling it in the Recall Mode. It does
not appear on the Stopwatch Mode screen.
To measure times with the stopwatch
Elapsed Time
A
A
➤
Start
Stop
Lap/Split Times
A
➤
D
Start
Lap/Split
Note
Pressing D to perform a lap/split time operation freezes the lap/split time at that
point on the display for about eight seconds. After that, the display returns to normal
stopwatch time measurement.
During a stopwatch time measurement operation, the upper part of the display
shows the hour digit and the current lap/split number, the center part shows the
current split time, and the lower part shows the current lap time.
When the pacer signal is turned on, it sounds for the first 30 seconds after you start
a stopwatch time measurement operation. After that, the pacer signal sounds for 30
seconds whenever you press B.
If the pacer signal does not sound even though you have it turned on, press B to
change the positions of the lap time and split time on the display. This should cause
the pacer signal to sound.
Selecting the Stopwatch Screen Format
The following shows how you can control the position of the lap time and split time on
the stopwatch screen.
Lap/Split number
Lap time
Press B.
Split
➤
time
Lap/Split
Lap time
Split time
indicator
The Lap/Split indicator uses arrows to indicate the location the lap time and split
(elapsed) time.
When you first start a stopwatch operation by pressing A, both the center part and
the lower part of the display show minutes, seconds, and 1/100 second. Whenever
the time shown in the lower part of the display is greater than 60 minutes, the display
format changes to show hours, minutes, and seconds. Whenever the time in the
center part of the display is greater than 10 hours, the display format changes to
show hours, minutes, and seconds.
A
A
D
➤
➤
➤
Re-start
Stop
Clear
A
D
➤
D
➤
➤
Next Lap/
Stop
Clear
Split
Minutes
Hours
Seconds
More than 10 hours
1