Casio 2572 사용자 설명서
{카테고리_이름} Casio 2572에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2572 4 페이지.
페이지 인쇄
MO0404-EB
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
• The longitude, lunitidal interval, Moon phase indicator, and tide graph data that
appear on the display of this watch are not intended for navigation purposes.
Always use proper instruments and resources to obtain data for navigation
purposes.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of tidal
movements only.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping
Moon phase indicator
Tide graph
PM
indicator
Day of week
Month – Day
Hour : Minutes Seconds
To set the time and date
Year
3. When the setting you want to change is flashing, use D and B to change it as
described below.
To change this setting
Seconds
Hour, Minutes, Year,
Month, Day
12/24-Hour Format
4. Press A twice to exit the setting screen.
• The first press of A displays the GMT differential setting screen. Pressing A again
exits the setting screen.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Home Site Data
Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed
properly unless Home Site data (GMT differential, longitude, and lunitidal interval) is
configured correctly.
• The GMT differential is the time difference of the time zone where the site is located
from Greenwich Mean Time.
• Note that you must add one hour to the GMT differential for your time zone
whenever you change to Daylight Saving Time. Subtract one hour when you change
back to Standard Time.
• The lunitidal interval is the time elapsing between the Moon's transit over a meridian
and the next high tide at that meridian. See "Lunitidal Interval" for more information.
• This watch displays lunitidal intervals in terms of hours and minutes.
• The "Site Data List" and "Lunitidal Interval List" provide GMT differential, longitude,
and lunitidal interval information around the world.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch and whenever you have the battery replaced. Change these
settings to match the area where you normally use the watch.
GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
USER'S GUIDE 2572
Warning!
Timekeeping Mode
Press C.
Use the Timekeeping Mode to set and view the current
time and date.
• The tide graph shows tidal movements for the current
date in accordance with the current time as kept in the
Timekeeping Mode.
• The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
Important!
• Moon phase, tide graph data, and Moon/Tide Data
Mode data will not be displayed properly unless the
Timekeeping Mode current date and time settings and
Home Site data are configured correctly. See "Home
Site Data" for more information.
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds
Hour
12/24-Hour
Day
Month
Year
Perform this button operation
Press D to reset to 00.
Use D (+) and B (–) to change the setting.
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
About This Manual
(Light)
Moon / Tide Data Mode
Dual Time Mode
To configure Home Site data
GMT differential
4. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
GMT differential
Longitude
Lunitidal
Minutes
Interval Hours,
Minutes
5. Press A to exit the setting screen.
Format
Moon/Tide Data
Moon phase indicator
Tide gragh
Moon age
Moon/Tide Data Screens
Each press of A in the Moon/Tide Data Mode toggles between the Moon Data
screen and the Tide Data screen.
Moon Data Screen
Moon phase indicator
• When you enter the Moon/Tide Data Mode, the data that appears first is the Moon
data (Moon age and Moon phase indicator) for the current date as kept by the
Timekeeping Mode.
To view the Moon data for a particular date
While the Moon Data screen is displayed in the Moon/Tide Data Mode, use D (+) and
B (–) to display the date whose Moon data you want to view.
• You can select any date from 2000 to 2039.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
Coutdown Timer Mode
Stopwatch Mode
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the GMT differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
GMT
Lunitidal Interval
Longitude
differential
Hours
Screen
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –11.0
to +14.0, in 0.5-hour unit.
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of
179°W to 180°E, in 1-degree units.
Use D (+) and B (–) to change the setting.
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time for the Home Site.
• If you suspect that the Moon/tide data is not correct for
some reason, check the Timekeeping Mode data
(current time, date, and Home Site settings), and make
changes as required.
• See "Moon Phase Indicator" for information about the
Moon phase indicator and "Tide Graph" for information
about the tide graph.
• All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
Tide Data Screen
Moon age
Time
Press A.
Year Month – Day
Alarm Mode
Lunitidal Interval
Minutes
Tide gragh
1