Danfoss HP75-1 지침 - 페이지 2

{카테고리_이름} Danfoss HP75-1에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Danfoss HP75-1 4 페이지. Electronic programmable heat pump thermostats with integral/remote sensor

페이지 인쇄

Setting record for thermostat set for

six events each day

Format

CLG

HTG

CLG

HTG

Pre-set programmes, Monday to Friday

25.0°C

20.0°C

27.2°C

15.0°C

25.0°C

6:30

8:30

Actual User Settings, Monday to Friday

1 (Monday)

2 (Tuesday)

3 (Wednesday)

4 (Thursday)

5 (Friday)

Pre-set Programmes, Saturday & Sunday

27.2°C

20.0°C

27.2°C

20.0°C

25.0°C

7:30

9:30

Actual User Settings, Saturday & Sunday

6 (Saturday)

7 (Sunday)

If the unit is to operate in 5/2 day mode, then only days 1 and 6 need be completed.

NOTES ON SETTING EVENT TIMES

(Assumes unit is in 6 events/day mode)

If, during the event checking and setting procedure, no buttons are

pressed for more than two minutes then the HP75 will return to RUN

mode automatically. If this appears to have occurred, it is advisable to

re-check the program to ensure that it is as required.

When setting event times and temperatures it is not possible to set

event times out of chronological order.

Event 1 may be set at any time from 0:00AM to 11:59PM (but would

normally be in the morning).

Event 2 may be set at any time between event 1 and 23 hours, 59

minutes after event 1.

Event 3 may be set at any time between event 2 and 23 hours, 59

minutes after event 1.

Event 4 may be set at any time between event 3 and 23 hours, 59

minutes after event 1,.... and so on.

32°C

31°C

30°C

29°C

28°C

COOLING

27°C

26°C

25°C

24°C

5°C

23°C

FACTORY

DEAD

22°C

PRE-SET

BAND

21°C

PROGRAMME

20°C

19°C

18°C

17°C

16°C

HEATING

15°C

14°C

13°C

MIDNIGHT

3:00

6:00

9:00

32°C

31°C

30°C

29°C

28°C

COOLING

27°C

26°C

25°C

24°C

23°C

EXAMPLE

3°C

22°C

USER SET

DEAD

21°C

BAND

PROGRAMME

20°C

Manual overide

19°C

MANUAL OVERRIDE = USED

18°C

to raise temperature by 2°C.

AT 9 AM TO RAISE

17°C

TEMPERATURE BY 2°C.

16°C

Programmed 3°C dead band

HEATING

PROGRAMMED 3°C DEAD

15°C

BAND MAINTAINED.

maintained.

14°C

13°C

MIDNIGHT

3:00

6:00

9:00

Event Numbers

CLG

HTG

CLG

HTG

CLG

HTG

CLG

20.0°C

27.2°C

15.0°C

25.0°C

20.0°C

27.2°C

11:30

13:30

16:30

20.0°C

25.0°C

20.0°C

25.0°C

21.1°C

27.2°C

11:30

13:30

16:30

12:00

15:00

18:00

21:00

used at 9am

12:00

15:00

18:00

21:00

Setting record for thermostat set for

Format

HTG

15.0°C

22:30

1 (Monday)

2 (Tuesday)

3 (Wednesday)

15.0°C

22:30

4 (Thursday)

5 (Friday)

6 (Saturday)

7 (Sunday)

If the event time being set is moved past midnight into the following day

then the number of the following day will blink.

00:30

12:30

When using the + button to adjust events 1 to 5 and the event time

being adjusted becomes the same as the following event time, then

both are changed simultaneously. This applies to all subsequent event

times reached and is demonstrated in the diagram on the lower left.

When using the - button to adjust events 2 to 6 and the previous event

time is reached the - button ceases to respond.

The factory pre-set programme may be reinstated by pressing the

recessed RESET button. This will however reinstate all the factory pre-

set conditions so that the clock type and temperature scale may also

have to be re-set.

MIDNIGHT

In the diagram opposite, event 2 has been moved to 3:30PM. Note that

events 3 & 4 have also been moved to that time and that the following

control temperature will be that of event 4.

It is possible to move events past midnight into the following day when

the day number will blink in the display, see the display diagram in the

notes on setting event times.

MIDNIGHT

two events each day

Event Number

CLG

HTG

CLG

HTG

Time

TIme

Pre-set programmes, Monday to Friday

25.0°C

21.1°C

Off

15.0°C

8:30

17:30

Actual User Settings, Monday to Friday

Pre-set Programmes, Saturday & Sunday

Off

8:30

17:30

Actual User Settings, Saturday & Sunday

15.0°C

Event 6 on day 6 set after

midnight.