Danfoss TP2 설치 및 사용자 지침

{카테고리_이름} Danfoss TP2에 대한 설치 및 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Danfoss TP2 4 페이지. Electronic programmable room thermostats

페이지 인쇄

TECHNICAL SPECIFICATION

Control Temperature Range

Power Supply

Switch Action

Switch Rating

Temperature Accuracy

Timing Accuracy

Enclosure Rating

Max. Ambient Temperature

Designed to meet BS EN60730-2-9

Overall Dimensions

Control Pollution Situation

Rated Impulse Voltage

Ball Pressure Test

Power Reserve

FEATURES

Controls central heating systems to provide different room

temperatures up to 6 times a day.

The TP3 and TP5 have one programme for Monday to Friday,

with a different programme for Saturday and Sunday.

TP2 and TP3 have minimum temperature setting of 16°C, ideal

for use in elderly persons accommodation.

Setting the TP4 and TP5 to the lowest temperature will

effectively switch off the heating, whilst providing frost protection

for the controlled area.*

A constant low temperature is easily selected while away from

home, for example, when on holiday.

Battery operated. Ideal for low voltage control circuits, e.g.

some combi-boilers, as well as for mains voltage circuits.

Batteries can be changed without loss of programme.

Wiring conversion chart for common room thermostats included.

This low temperature selection should not be used for Frost

Protection if some parts of the heating system are in an exposed

location.

INSTALLATION INSTRUCTIONS

NEW INSTALLATION

Choose a fixing position where the thermostat will sense the room

temperature without being affected by draughts or heat sources

such as radiators, open fires or direct sunlight. Fix at height of

approximately 1.5 metres from the floor.

Cable entry is from behind if fitted to a single gang flush box, or

from above, below or from the left if surface fixed cable is used.

Fig.1. shows fixing hole dimensions and the clearance required for

the removal of the sliding cover, and for air flow over the sensor.

Standard M3.5 screws are used to fix the thermostat to a flush box,

or No.6 woodscrews and wall plugs of adequate length should be

used for surface fixing.

: 5-30°C

: 2 x AA / MN 1500 / LR6 High Quality

Alkaline Batteries

: 1 x SPDT, type 1B

: 220/240Vac, 50/60Hz, 6(2)A

: ± 1°C

: ± 1 min/month

: IP20

: 45°C

: 99 wide x 81mm high x 34 deep

: Degree 2

: 2.5Kv

: 75°C

: 1 minute for battery change

This product complies with the following EC Directives :

Electro-Magnetic Compatibility Directive.

(EMC) (89\336\EEC), (92\31\EEC)

Low Voltage Directive.

(LVD) (73\23\EEC), (93\68\EEC)

Fig.1. Fixing centre and clearances.

REPLACING AN ORDINARY ROOM THERMOSTAT

Switch OFF the power to the central

heating system.

Carefully note which wire colours are

connected to which terminal numbers

of the existing thermostat.

If the existing thermostat has no

indication of the numbers of each of

its terminals then a qualified electrician

should be called before proceeding

any further.

Remove the existing thermostats

mounting plate from the wall, and

prepare the wall to receive the

Programmable Room Thermostat. Refer to Fig.1. for dimensions.

Connect the wires to the new thermostat referring to the wiring

conversion chart overleaf.

NOTE:

Some existing thermostats will have a Neutral wire and/or an Earth

wire connected. These wires must NOT be connected to the new

terminals, but made electrically safe and coiled in the recess at the

back of the new thermostat. If in any doubt about the function of every

wire connected to the existing thermostat, call a qualified electrician for

advice.

Live

Switched

input

output

OFF

COM

Fig.2. Terminals on rear

of unit