Free2Talk Sun-Lite 사용자 설명서

{카테고리_이름} Free2Talk Sun-Lite에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Free2Talk Sun-Lite 2 페이지.

페이지 인쇄

Free2Talk

'Sun-Lite'

USER GUIDE

Thank you for purchasing the cutting edge of hands-free,

wireless technology of Free2Talk.

This user guide will get you started and ready to make the

most of your Bluetooth Solar Visor Carkit.

The Solar Visor Carkit is compatible with most Bluetooth

mobile phones. Fully portable, it is an ideal wireless

communication solution for in-car or office use within a

maximum range of 10 meters (32 feet). Echo Cancellation and

Noise Suppression are built integrally allowing the Bluetooth

Carkit to provide you with impeccable sound quality in full

duplex mode.

1. Appearance and Function

(1) Speaker

(2) Microphone

(3) LED

(4) Charging Socket

(5) Mute Button

(6) MFB Button (Multi-Function

Button)

(7) Volume Increase (+)

(8) Volume Decrease (-)

(9) Solar Panel

(10) Windshield Mount

2. Recommend Installation Position

It is recommended that the Carkit is positioned on to the top

of the windshield as shown in the pictures below:

WARNING: Do not place or store the Carkit over the area of

the automobiles safety airbag deployment, or it may cause

serious injury when a safety airbag deploys.

3. Charging Your Carkit

The Carkit comes with a built-in rechargeable battery. Prior to

using the Carkit, it is recommended to charge the battery fully

for the first time.

Using the Car charger

• Insert the car charger firmly into the charging slot.

• Full charge time is approximately 2 hours.

Using Solar Power

• Ensure that the Carkit is installed to the recommended

installation position (as illustrated above).

• The Carkit recharges itself as soon as it is receives adequate

sunlight.

Note: The solar charging gauge is if the Carkit receives

sufficient sunlight for 2 hours, it equates to extending the

Talk-time by 1 hour or 50 hours of Standby Time.

WARNING: Do not attempt to charge the Carkit with any

charger other than the one provided.

4. Turning ON/OFF the Carkit

Power On: Press and hold the "MFB" button for four seconds

and the flashing blue LED light indicator comes.

NOTE: Do not hold the button down for more than 8 seconds

when turning on the Carkit or else it may switch to its pairing

mode. If this happens, turn off the Carkit and repeat the

process for turning on the Carkit.

Power Off: Press and hold the "MFB" button until the LED

light indication goes off.

5. Pairing Carkit with Mobile Phone

Pairing is the process of connecting your Carkit with your

mobile phone. Before using the Carkit with your mobile phone,

you must pair both devices. If you wish to use your Carkit with

a different mobile phone, you must reinitiate the pairing

process with your intended Bluetooth mobile phone. The steps

below describe pairing instructions for a typical Bluetooth

enabled mobile phone.

(1) Place the Carkit and mobile phone no more than 1 meter (3

feet) apart.

(2) Ensure the Carkit is turned off.

(3) Press and hold the "MFB" button for at least 6 seconds until

the LED flashes red and blue simultaneously, it is now ready for

pairing.

(4) Activate the pairing feature on your mobile phone. Refer to

your mobile phone's user guide.

(5) Select "Free2Talk BC902" from the list of searched devices

and enter the default pin code "0000", when prompted by

your mobile phone system.

(6) When pairing is completed, the Carkit is under the standby

mode with the blue LED flashing at a 3 second interval

NOTE: If the pairing cannot be completed within 2 minutes

after the pairing mode is activated, the Carkit will power off

automatically. Please repeat steps above to pair the Carkit and

mobile phone again.

6. Connection Link/Between Carkit and Mobile Phone

Your mobile phone will always indicate a connection icon

whenever your Carkit is paired. If the icon is not present, a

reconnection can be established by manually selecting the

Carkit from your mobile phone's Bluetooth menu. If your Carkit

is set as an authorized Bluetooth device on your mobile phone,

an automatic reconnection can be established by pressing the

headset's MFB button once.

Note: Your Carkit will be automatically switched off when it is

disconnected from a paired device for more than 10 minutes.

This special feature is incorporated to maximize your Carkit's

standby/talk time. To reinstate the connection, simply repeat

the process for turning Carkit on.