Conrad 2377686 사용 설명서 - 페이지 3

{카테고리_이름} Conrad 2377686에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Conrad 2377686 8 페이지. Led orientation light with pir sensor

페이지 인쇄

Operating Instructions

LED Orientation Light with PIR Sensor

Item no: 2377686

1 Intended use

The product is a battery-operated wall light. The wall light supports two operation modes. In manual

mode, the light is controlled by a mechanical switch. In automatic mode, the motion sensor (PIR) triggers

other lights on the same frequency channel when motion is detected.

The product is intended for indoor use only. Do not use it outdoors.

Contact with moisture must be avoided under all circumstances.

If you use the product for purposes other than those described, the product may be damaged.

Improper use can result in short circuits, fires, or other hazards.

The product complies with the statutory national and European requirements.

For safety and approval purposes, you must not rebuild and/or modify the product.

Read the operating instructions carefully and store them in a safe place. Make this product available to

third parties only together with the operating instructions.

2 Delivery contents

■

1x Wall light

■

1x Mounting plate

■

2x Screws

■

2x Wall plugs

■

1x Double-sided tape

■

Operating instructions

3 Latest product information

Download the latest product information at

low the instructions on the website.

4 Description of symbols

The symbol with the exclamation mark in the triangle is used to indicate important informa-

tion in this document. Always read this information carefully.

This product must only be used in dry, enclosed indoor areas. It must not become damp or

wet.

This product is constructed according to protection class III.

5 Safety instructions

Read the operating instructions carefully and especially observe the safety informa-

tion. If you do not follow the safety instructions and information on proper handling,

we assume no liability for any resulting personal injury or damage to property. Such

cases will invalidate the warranty/guarantee.

5.1 General

■

The product is not a toy. Keep it out of the reach of children and pets.

■

Do not leave packaging material lying around carelessly. This may become dangerous playing mater-

ial for children.

■

If you have questions which remain unanswered by this information product, contact our technical

support service or other technical personnel.

5.2 Handling

■

If it is no longer possible to operate the product safely, take it out of operation and protect it from any

accidental use. Safe operation can no longer be guaranteed if the product:

– is visibly damaged,

– is no longer working properly,

– has been stored for extended periods in poor ambient conditions or

– has been subjected to any serious transport-related stresses.

■

Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

■

Consult an expert when in doubt about the operation, safety or connection of the appliance.

5.3 Operating environment

■

Do not place the product under any mechanical stress.

■

Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.

■

Protect the product from high humidity and moisture.

■

Protect the product from direct sunlight.

■

Do not switch the product on after it has been taken from a cold to a warm environment. The con-

densation that forms might destroy the product. Allow the product to reach room temperature before

you use it.

■

Never operate the product in direct proximity of strong magnetic or electromagnetic fields or transmit-

ter aerials or HF generators. Doing so can prevent the product from functioning properly.

5.4 Batteries

■

Correct polarity must be observed while inserting batteries.

www.conrad.com/downloads

or scan the QR code shown. Fol-

■

The batteries should be removed from the device if it is not used for a long period of time to avoid

damage through leaking. Leaking or damaged batteries might cause acid burns when in contact with

skin, therefore use suitable protective gloves to handle corrupted batteries.

■

Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk,

that children or pets swallow them.

■

All batteries should be replaced at the same time. Mixing old and new batteries in the device can lead

to battery leakage and device damage.

■

Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-rechargeable

batteries. There is a risk of explosion!

5.5 LED light

■

Do not look directly into the LED light!

■

Do not look into the beam directly or with optical instruments!

6 Installing batteries

Note:

If an insulating strip protrudes from the battery compartment, batteries are installed already. Pull the

strip out to establish the power supply.

RECONDITIONS

Prepare the required number of batteries of the correct type as stated in the section "Technical data".

1. Unlock the battery compartment cover and remove it.

2. Insert the batteries into the battery compartment observing the polarity markings in the compartment.

3. Attach the compartment cover and lock it. If a seal is present, make sure it sits correctly and you do

not damage it when attaching the cover.

7 Mounting

7.1 Selecting mounting locations

When you choose mounting locations for the wall lights, it is important to consider the maximum wireless

range between the lights and the limitations of the motion sensor (PIR).

7.1.1 Placement diagram

When selecting mounting locations, observe the values given in the diagrams for optimal performance.

Wireless range

max.

6 m

7.1.2 Factors affecting wireless signal strength

Surrounding objects can reduce the strength of the wireless signal:

■

Walls and reinforced concrete ceilings

■

Coated or vaporised insulating glass panes

■

Proximity to metallic and conductive objects (e.g., radiators)

■

Broadband interference, e.g. in residential areas (DECT phones, mobile phones, radio headsets,

wireless speakers, wireless weather stations, baby monitoring systems, etc.)

■

Electric motors, transformers, power-supply units and computers

■

Poorly shielded or uncovered computers or other electrical appliances

7.1.3 Factors affecting motion detection

The passive infrared (PIR) motion sensor reacts to changes in temperature, e.g. when a person or animal

enters the detection area.

■

Position the sensor so the object moves across the detection area.

■

The correct installation height should be observed.

■

Do not point the sensor at radiators, lights, or objects with varying temperatures (e.g. electronic equip-

ment), and objects that may move due to the flow of air. This may trigger the sensor unintentionally.

■

Do not install the product behind glass.

■

Keep the sensor away from direct sunlight.

7.2 Mounting with screws

Mount the light using screws and wall plugs.

WARNING

Concealed wires. Risk of deadly electric shock when drilling.

● Check for concealed wires before drilling.

1. Drill holes and insert wall plugs.

2. Use screws to fix the mounting plate in place.

3. Hang the light on the mounting plate.

Motion sensor (PIR)

Height

<1.5 m

3 - 5 m

110 °

y(°)