DANLERS HBA PIR SP DSIP 설치 참고 사항

{카테고리_이름} DANLERS HBA PIR SP DSIP에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. DANLERS HBA PIR SP DSIP 2 페이지. High bay pir occupancy switches with dsip dimming

페이지 인쇄

Variants

Presence detection variants:

Each of these High bay PIR occupancy switches with DSIP dimming are also

available with presence detection (does not require a momentary (retractive)

wall switch).

Troubleshooting

The load will not switch on:

• The moving body is not emitting more IR than the background.

(Person wearing insulating clothing in a warm environment)

• Person is too far from the PIR switch, see detection diagram.

• Person is moving unusually slowly (perhaps when testing).

Precautions and Warranty

This product conforms to BS EN 60669-2-1. Product complies to Class 2 insulation.

Please ensure the most recent edition of the appropriate local wiring regulations are observed

and suitable protection is provided e.g. 6 amps over current, 1kV over voltage. Please ensure

that this device is disconnected from the supply if an insulation test is made.

This product is covered by a warranty which extends to 5 years from the date of manufacture.

Products available from DANLERS

• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers

• Photocells • Radio remote controls • Time lag switches • Outdoor security switches

• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products

Please call for more information or a free catalogue, or visit our website.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388

E-mail: [email protected]

Web: www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

23/08/16

INS281 HBA PIR (xx) DSIP

High bay PIR occupancy switches with DSIP dimming

HBA PIR ND DSIP

HBA PIR SP DSIP

DANLERS High bay passive infra-red occupancy (absence detection) switches with

closed loop control can be used to control high frequency DSI dimmable ballasts.

They each incorporate a passive infra-red quad sensor to detect movement of a

warm body within their detection zone (diagram A) and a photocell to monitor the

ambient light level.

Each of the controls can be mounted directly onto solid ceilings or onto a range of

different mounting boxes.

The high bay controls are available in three types - each with a particular detection

pattern which is optimised for particular applications.

HBA PIR ND DSIP: Narrow Detection version is ideal for covering storage aisles.

HBA PIR SP DSIP: Spot Detection version is ideal for smaller areas, such as the

entrances to storage aisles.

HBA PIR WD DSIP: Wide Detection version is ideal for large open areas, such as

factories, sports halls and entrance halls.

Functions

When entering a zone of detection a momentary wall switch must be pressed to send a

signal to the PIR to switch the lights ON at maximum and start the closed loop control

to maintain the preset lux level value (LUX) between 30 and 1000 lux (default value

1000 lux). See diagram C.

NO BACKGROUND ILLUMINANCE RUN ON TIME SET: If no further movement is

detected the lights will switch OFF after the set PIR hold timer (TIME) has expired. This

time lag can be set via the TIME adjuster to 10 seconds, 20s, 40s, 80s, 2m30s, 5m,

10m, 20m or 40 minutes (default value 10 seconds). See diagram B. Alternatively, the

momentary switch can be pressed for more than 2 seconds to switch the lights OFF.

BACKGROUND ILLUMINANCE RUN ON TIME SET: If no further movement is detected

the lights will FADE to minimum after the set PIR hold timer (TIME) has expired OR

if the momentary wall switch is pressed for more than 2 seconds. The lights will then

stay at minimum until the background hold timer (RUN ON) has expired. The RUN

ON time can be set via the RUN ON adjuster to 0, 1, 2, 5, 10, 15, 20, 30 minutes or

infinite (default value is 0). See diagram C.

If the momentary wall switch is pressed for less than 2 seconds while the background

hold timer is counting down, the lights will switch ON at maximum and start the closed

loop control to maintain the set lux level value.

These PIR switches can switch up to:

6 amps (1500W) of dimmable fluorescent lamps.

2 amps (500W) of CFL, LED Drivers and LED lamps and fittings.

These controls have an integral DSI Power Supply Unit suitable for use with up to 12

DSI ballasts, assuming each ballast has a constant current output of 1mA.

Installation notes

HBA PIR WD DSIP