DANLERS CEFL PIR 설치 참고 사항 - 페이지 10

{카테고리_이름} DANLERS CEFL PIR에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. DANLERS CEFL PIR 15 페이지. Ceiling flush mounted pir occupancy switch
DANLERS CEFL PIR에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

1. Troubleshooting

Press 'Override'. New screen appears 'Override'. Select a timed duration (10sec to

23hrs 59min 59sec) for the override or 'Indefinitely' (see diagram 30).

Calibrate

The photocell calibration process removes the site specific addition of artificial light from

any decision to switch the lights on/off. Calibration is recommended to take place when

ambient light levels are low (preferably at night or with daylight excluded as far as possible,

from the calibration measurement).

Prior to Calibration, ensure the lighting load and other surrounding artificial lighting

has been turned ON for 15 minutes or more to allow the load to stabilise. If required,

the lighting load can be forced ON by activating the OVERRIDE feature within the

ControlZAPP DEVICE OPTIONS menu.

Press 'Calibrate'. New screen appears 'Calibrate'. Press 'Start Calibration'. (or 'Cancel')

The calibration process takes approximately 10 seconds.

When complete the information in the blue box should inform you that the device is

successfully Calibrated with a calibration value. (See Diagram 31).

If the device has been previously calibrated you will be promted to 'Recalibrate'.

Setup

SWITChING ONLy:

Allows you to set the threshold switching level used for the 'Daylight

Control' feature and can only be activated once the device is Calibrated. It is essential that

some natural daylight is available for this feature to work. If no natural daylight is available

disable the 'Respond to Daylight' option in the PROFILE'S Modes.

Press 'Setup'. New screen appears with each of the MODES within the downloaded

PROFILE shown along the top. The MODE in use is indicated with a blue line

underneath. For each MODE listed it will show if the 'Daylight Control' feature is ON or

OFF and also if the 'Turn OFF above threshold' feature is ON or OFF.

If the selected MODE has 'Daylight Control' ON, an adjustment slider is available

to set the threshold value - left (dark) and right (light) (See diagram 32). The slider also

shows the current light level as read from the device. When the adjuster is slid to the left

it lowers the light level at which the lighting load will switch ON. When the adjuster is slid

to the RIGHT it raises the light level at which the lighting load will switch ON.

If the control light level is too low (not enough natural light) a red warning box is shown

warning you to resite the device where it is seeing more natural daylight (recalibrate and

setup) OR increase control light level ie. slide adjuster to the right.

The Override switch option will turn the load ON or OFF as required.

If MODE has 'Daylight Control' OFF, the threshold adjustment slider is not available.

If the device's 'Always turn off when above threshold' value is ENABLED: Progress bar

is GREEN if threshold light level plus calibration value is less than or equal to 1000.

Progress bar is RED if threshold light level plus calibration value more than 1000.

If the device's 'Always turn off when above threshold' value is DISABLED: Progress bar

GREEN if threshold light level less than or equal to 1000. Progress bar RED if threshold

light level more than 1000.

For an individual MODE: Press 'Save' button to upload the new threshold light level

value to the device for that mode.

Press 'Apply to all' button to upload the threshold switching light level to the device for

ALL MODES in that Profile.

DIMMING WITh DALI BALLAST OR 1-10V BALLAST:

Allows you to set the threshold Daylight Linked Dimming level used

for the 'Daylight Control' feature and can only be activated once

the device is Calibrated. It is essential that some natural daylight is

available for this feature to work. If no natural daylight is available

disable the 'Respond to Daylight' option in the PROFILE'S Modes.

Press 'Setup'. New screen appears with each of the MODES within

the downloaded PROFILE shown along the top. The MODE in use

is indicated with a blue line underneath. For each MODE listed it

will show if the Daylight Control' feature is ON or OFF and also if

the 'Turn OFF above threshold' feature is ON or OFF.

DIMMING WITh DALI BALLAST

If the selected MODE has 'Daylight Control' ON, and the

dimming feature is selected three adjustment sliders are

available to set the threshold values.

The upper slider (see diagram 33a) dims the connected lighting

load to the the lux level which you wish to maintain. This is done is

real time, allowing a short period for the lighting load to stabilise.

NOTE: If a precise LUX reading is required (e.g. 500 lux) then a

calibrated lux meter at the working plane is required.

Diagram 29

Diagram 30

Diagram 31

Diagram 32

Diagram 33a

Diagram 33b

Diagram 33c

PAGE 8