Danpex CFM3400C40 사용자 설명서 - 페이지 4

{카테고리_이름} Danpex CFM3400C40에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Danpex CFM3400C40 4 페이지. Cfm3400 series bridge, fast ethernet 10/100 base-tx to 100 base-fx

페이지 인쇄

Connecting to TP, Fiber Device

Converter

AUTO, FORCE selectable: Bit 1, 2, & 3 of S1

TP Port

AUTO: 10/100 N-Way auto-negotiation

10/100TP

FORCE: 100 or 10, FDX or HDX

Converter

100Mbps duplex selectable: Bit 5 of S1

Fiber Port

FDX for 100FDX fiber link partner, default

100FX

HDX for 100HDX fiber link partner

Fig. 11 S1-Bit 1, 2, 3, 4, & 5 Configuration and Setting

S1-1

TP port mode

: AUTO (Default) or FORCE

S1-2

TP port speed

: 100 (Default) or 10 when TP at FORCE

S1-3

TP port duplex

: FDX (Default) or HDX when TP at FORCE

S1-4

LFP

: LFP enabled (Default) or disabled

S1-5

Fiber port duplex

: 100FDX (Default) or 100HDX

Note:

S1-2 and S1-3 will take effect only when S1-1 is set at TP-FORCE.

Warning:

When TP N-Way port is connected to TP 100FDX (FORCE mode) instead N-Way

—

partner, it will result in 100HDX mode with invalid collision signal

Ensure that all network nodes are configured at an identical operation mode.

—

Improper operation and flow control modes between TP and fiber port

connections will render the LAN at work poorly

Cable Connection Parameter

100Base-X network allows 512-bit time delay between any two node-stations in a

collision domain. Switch-based Media Converter breaks up TP and fiber segments'

collision domain to extend the cabling distance.

•

TP Cables Limitations: Category 5 or better, up to 100m

•

Converter Fiber Cable Limitations:

SC/ST Converter Models

Multi-Mode Half-Duplex

Multi-Mode Full-Duplex

Single-Mode Half-Duplex

Single-Mode Full-Duplex

20/40/60km

•

Self Powering USB Cable Limitations: Type B to Type A USB cable, up to

412m

2 km

412m

Warning

When Self Powering cable is being used, be sure that the USB port is operational

If connects to a PC/Notebook computer, the USB port driver need not be loaded

in order for the converter to draw power from cable provide that (a) is valid

Battery consumption will be higher than usual if use notebook on battery

10.

TP-Fiber Technical Specifications

•

Standards: IEEE 802.3u 10/100Base-TX, 100Base-FX

•

Models:

Model

Connector

CFM3400C

1310nm Multi-Mode Duplex-SC

CFM3400T

1310nm Multi-Mode Duplex-ST

CFM3400C20

1310nm Single-Mode Duplex-SC 20km

CFM3400C40

1310nm Single-Mode Duplex-SC 40km

CFM3400C60

1310nm Single-Mode Duplex-SC 60km

•

Cable/Max Distance:

UTP

Category 5, up to 100m

Multi-Mode Fiber

50/125, 62.5/125, or 100/140µm, up to 2km

Single-Mode Fiber

8.3/125, 8.7/125, 9/125, or 10/125µm, up to 20~60km

•

LED Indicators: POWER, TP LNK/ACT, 100, FX LNK/ACT, FDX/COL

•

Data Transfer Rate:

Speed

Forwarding Rate

100Mbps

148,800 PPS

10Mbps

14,880 PPS

•

Flow Control:

IEEE 802.3x compliant for full-duplex, and

Back-Pressure flow control for half-duplex

•

Power Requirement:

1A@+5V DC from AC-DC Adapter

0.5A@+5V DC from USB Port

•

Ambient Temperature: 0° to 50° C

•

Humidity: 5% to 90%

•

Dimensions: 26.2 x 70.3 x 94 mm (H x W x D)

•

Complies with FCC Part 15 Class A and CE Mark

Note: For connecting this device to Router, Bridge, or Switch, please refer to the

corresponding device's Technical Manual.