Construction Solutions DBX1000 설치 및 제품 설명서 - 페이지 2

{카테고리_이름} Construction Solutions DBX1000에 대한 설치 및 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Construction Solutions DBX1000 2 페이지. Recessed vent receptacle

페이지 인쇄

7801 E. Gray RD Suite 110

Scottsdale, AZ 85260

Material used in the DBX 1000 meets UL94 HB Flammability Testing and is recognized by Underwriters Laboratories Inc.

Representative samples of this component have been evaluated by UL and meet applicable UL requirements.

For optimum results, install the DBX1000

Box Installation - 16 Inch On-Center Spacing:

6. Orient box to match desired venting direction, score & remove appropriate, top or rear, 4-inch

vent pipe knock out. Allow minimum of 4 inches of vent of pipe to extend inside box

7. If gas line is to be installed, locate 1⅝ straw clamp on top of box. Cut the webs between the

8 fins with a utility knife. Push the gas line through the straw clamp. The fins will flex inward

holding the pipe.

8. Slide box into position taking care to correctly align vent pipe and gas pipe (if present).

9. Spacing tabs will automatically position box so that bottom, inside edge is from 2¼ to 2⅝

inches above unfinished floor to allow clearance between trim ring and finished floor

covering. Tabs may be removed if a different spacing is desired.

10. Attach box directly to both right and left studs using the six flange screw holes. Screws are

recommended for mounting.

Box Installation - 24 Inch On-Center Spacing:

7. Orient box to match desired venting direction, score & remove appropriate 4-inch vent pipe

knock out. Allow minimum of 4inches of vent of pipe to extend inside box.

8. If gas line is to be installed, locate 1⅝ straw clamp on top or bottom of box. Cut the webs

between the 8 fins with a utility knife. Push the gas line through the straw clamp. The fins

will flex inward holding the pipe.

9. Slide box into position taking care to correctly align vent pipe and gas pipe (if present).

10. Spacing tabs will automatically position box so that bottom, inside edge is from 2¼ to 2⅝

inches above unfinished floor to allow clearance between trim ring and finished floor

covering. Tabs may be removed if a different spacing is desired.

11. Attach one side of box directly to stud using the three flange screw holes.

12. Snap in the two mounting straps on the other side of the box and attach these to the second

stud using the strap screw holes. Screws are recommended for mounting.

Trim Instructions:

5. Leave 1¾ inches between inside edge of box and

end of baseboard to allow for trim ring clearance.

6. Snap trim ring into opening, no caulking required.

7. Leave unfinished or paint with desired color.

½"

⅝''

1¼

16 ½"

6" Wall DBX 1000

Recessed Vent Box

Construction Solutions

www.newconstructionsolutions.com

Vent Pipe Knockouts

10 ⅛"

⅝"

Straw

Clamp

Rear

Knockout

Straw Clamp

(on Bottom)

TRIM NOTE:

1¾" Clearance to

Edge of Baseboard

TRIM NOTE:

2¼" to 2 ⅝" Clearance

to Unfinished Floor

Ph: (480)346-8240

Fax: (480) 346-8250

recessed vent receptacle for 6 Inch Walls as follows:

 Box made from High Impact Polystyrene ("HIPS")

 Meets UL94 HB Flammability Testing

 Install in up to 24" on center location, brackets

included

 Easy to remove 4" knockouts

 Top and Bottom Straw clamps for gas pipe

 Snap on trim ring accommodates up to ¾" drywall

 US Patented Product 6,938,640

1¾"

Mounting Straps

For 24" OC

DBX1000 Recessed Vent Receptacle

Installation Guidelines &

Product Information

⅛

¼"