Duratax NITRO DEMON 조립 및 작동 매뉴얼 - 페이지 3

{카테고리_이름} Duratax NITRO DEMON에 대한 조립 및 작동 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Duratax NITRO DEMON 20 페이지.

페이지 인쇄

REPAIR SERVICE

Repair service is available anytime.

• After the 90 day warranty, you can still have your Nitro

Demon repaired for a small charge by the experts at

DuraTrax's authorized repair facility, Hobby Services, at

the address listed on the front page of this manual.

To speed up the repair process, please follow the

instructions listed below.

1. Under most circumstances return the ENTIRE system: truck

and radio. The exception would be sending in a Stress-Tech

part. See the instructions under Stress-Tech Guarantee.

2. Make sure the transmitter is turned off, all batteries are

removed and fuel is drained from the tank.

3. Send written instructions which include: a list of all items

returned, a THOROUGH explanation of the problem, the

service needed and your phone number during the day. If

you expect the repair to be covered under warranty, be

sure to include a proof of date of purchase (your store

receipt or purchase invoice).

4. Also be sure to include your full return address.

SPECIFICATION & DESCRIPTION CHANGES

All pictures, descriptions and specifications found in this

instruction manual are subject to change without notice.

DuraTrax maintains no responsibility for inadvertent errors

in this manual.

SCREW INFORMATION

Do not use too much force when tightening self-tapping

screws into plastic. Overtightening will cause the threads in

the plastic to strip. We recommend that you stop turning a

self-tapping screw when you feel some resistance as the

head of the screw comes in contact with the plastic. Avoid

using powered screwdrivers when assembling this kit. They

tend to overtighten the screws. Do not use thread locking

compound on any self-tapping screws. The thread locking

compound may damage the plastic. IMPORTANT: Use

thread lock on any fastener that is threaded into metal or

fastened with a nut. Vibration from the engine will cause the

screws to loosen if thread locking compound is not used.

M3x14 Screw

3mm

14mm

M3x14

Self-Tapping

Screw

3mm

14mm

EQUIPMENT YOU WILL NEED

To operate the Nitro Demon RTR these items are required:

• Fuel (DuraTrax Red Alert fuel - DTXP0520)

• Air Filter Oil (DTXC2465)

• Glow plug wrench (DTXR1170)

• Hobby knife (HCAR0105), #11 blades (HCAR0211)

• It is also helpful to have a couple of extra glow plugs on

hand (O.S. #A3 plug - OSMG2690)

DuraTrax Nitro Starter Pack from - DTXP0200

For the Pre-Built version of the Nitro Demon, you will also need:

• 2-channel radio with one (1) standard servo and one (1)

high torque (70+ oz./in.) steering servo

• Twelve (12) "AA" batteries - Four (4) for the receiver and

eight (8) for the transmitter

• Glow plug starter (DuraTrax Rapid Heat- DTXP3000)

• Fuel bottle (DuraTrax Kwik-Pit Bottle - DTXP0125)

• Small bottle of thread locking compound (GPMR6060)

TOOLS YOU WILL NEED

To assemble the Pre-built version (DTXC0075), you will

need the following tools:

• #1 Phillips head screwdriver (DTXR0122)

• Flat blade screwdriver (DTXR0100)

• Needle-nose pliers (DTXR0300)

• Wire cutters or diagonal cutters (HCAR0630)

• Hobby knife (HCAR0105), #11 blades (HCAR0211)

• Drill with 1/4", 1/8", 5/64" (or 6mm, 3mm, 2mm) bits