DAPAudio D1226 사용자 설명서 - 페이지 13
{카테고리_이름} DAPAudio D1226에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DAPAudio D1226 19 페이지.
페이지 인쇄38. Channel 2 Gain:
Channel input level is determined by the Gain control. With the Gain control you can boost
the signal of each individual channel. Ad just the input- sensitivity in order to match the incoming
signals to the
39 /40 /41. Channel 2 Equalizer SECTION (HI / MID / LOW):
Use the 3 band equalizer to adjust the tone for each channel by using the HI, MID and LOW controls.
42. VU METER:
The stereo VU Meter allows you to monitor the dB levels of the Left and Right Master output.
43. Channel 2 Fader:
The fader controls the volume of a single channel. The channel faders should be positioned within the
range of -5dB to 0dB, leaving you with sufficient room to allow precise matching.
44. Fader Start Relay:
The Fader Start Relay function allows you to start CD playback simply by moving the Crossfader
to a side.
Front Functions
45. CD 1 Disc Holder
Place the disc in the holder. Press the Eject button to open and close the disc holder.
46. Microphone
47. Headphone
You can connect a pair of headphones with a minimum impedance of 32 Ohm to this stereo
jack should be wired as Tip=left, Ring=right and sleeve=ground.
48. CD 2 Disc Holder
Place the disc in the holder. Press the Eject button to open and close the disc holder.
49. SD Card 1 Slot
Slot for inserting SD/MMC c a rd . The c onta c ts of the c a rd m ust p oint d o w nw a rd s. The unit c a nnot rea d
c a rd s w ith a c a p a c ity of m ore tha n 4GB. The unit is not c om p a tib le to SDHC c a rd s a nd only sup p orts
the MP3 format.
50. SD Card 2 Slot
Slot for inserting SD/MMC c a rd . The c onta c ts of the c a rd m ust p oint d o w nw a rd s. The unit c a nnot rea d
c a rd s w ith a c a p a c ity of m ore tha n 4GB. The unit is not c om p a tib le to SDHC c a rd s a nd only sup p orts
the MP3 format.
Back Functions
51.
Mains Cord
Check the 115V/ 230V selector before connecting to the mains.
52. Fuse T1A 250V
Replace the fuse only by a fuse of the same type.
53. Power ON/OFF
This is the main Power switch. Press to turn the device on.
54. 115V/230V Selector
Before plugging the DS-CDJ-250MKII into any wall socket, make sure that the 115V/230V Selector is set
to the proper voltage.
55. Headphone
You can connect a pair of headphones with a minimum impedance of 32 Ohm to this stereo
jack should be wired as Tip=left, Ring=right and sleeve=ground.
56. Master Balanced Out L/R
Use these outputs to connect an amplifier with balanced inputs.
57. Record RCA Unbalanced Out
Use these to connect a recording device.
58. Master RCA Unbalanced Out
Use these outputs to connect an amplifier with unbalanced inputs.
59. Channel 2 Phono/ Line switch
The setting of this switch determines the input impedance/ sensitivity for the Channel 2 RCA input.
60. Channel 2 RCA Input
Use to connect either a Line level or Phono level device.
11
1
1