Apollo Smoke Detector XP95 설치 매뉴얼

{카테고리_이름} Apollo Smoke Detector XP95에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Apollo Smoke Detector XP95 2 페이지. Input/output unit
Apollo Smoke Detector XP95에 대해서도 마찬가지입니다: 설치 및 유지 관리 매뉴얼 (4 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (5 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (2 페이지)

페이지 인쇄

Protocol bit use:

Output Bit

Function

group mode

1 = off

0 = on

Alert tone

1 = on

0 = off

Evacuation tone

1 = on

0 = off

Fault Finding

Problem

Possible Cause

No response or missing

Incorrect address setting

Incorrect loop wiring (polarity reversed)

Analogue value 1

Sounder test failed

Analogue value 2

VAD failed

Analogue value 3

Sounder and VAD failed

Analogue value 4

Incorrect group address or address setting

Product fails to operate

Control panel has incorrect cause and effect programming

Incorrect group address setting

Tone Table

Part Number

Primary Tone

45681-707

DIN Tone (sweep) *

1200Hz - 500Hz for 1s

For further technical information please refer to PP2478.

Apollo Fire Detectors Limited, 36 Brookside Road, Havant, Hants, PO9 1JR, UK

Tel +44 (0)23 9249 2412 Fax +44 (0)23 9249 2754

Email: techsales@apollo-ﬁ re.co.uk Website: www.apollo-ﬁ re.co.uk

39214-789/Issue 1

Input Bit

Function

group mode conﬁ rmed

1 = group

0 = individual

Alert tone conﬁ rmed

1 = on

0 = off

Evacuation tone conﬁ rmed

1 = on

0 = off

Secondary Tone

Continuous*

850Hz

XP95 Sounder VAD Base DIN with Isolator

Installation Guide

General

This guide describes the installation of the following sounder

Part number

Product Description

45681-707

XP95 Sounder VAD Base (White) DIN with Isolator

45681-292

White Cap only

45681-293

Red Cap only

Connect the products only to control panels using the XP95 protocol.

The XP95 Sounder VAD Base combines a sounder with a visual alarm and a detector base in one unit.

The VAD is activated whenever the sounder is active and cannot be controlled separately.

The XP95 Sounder VAD Base with short circuit isolator has a yellow LED which illuminates through the mould-

ing if a short circuit is detected on the loop wiring (see Fig 2).

Note: The XP95 Sounder VAD Base is not suitable for outdoor use.

Mounting Instructions

The sounders may be secured to a UK or European standard conduit box or surface mounted (providing

there is access through the surface for cabling). If a detector is ﬁ tted, lock it if required by screwing in the

grub screw on the head with a 1.5mm hex driver (part no 29600-095)

The XP95 Sounder VAD Bases are ceiling mounted devices. For coverage volume information please refer

to PP2478.

Wiring Details

Note: This product is polarity sensitive (supply reversal protected) and will not function if wired incorrectly.

Connect the positive XP95 loop cables to the L2 terminals, the negative loop in to L1 IN and negative loop

out to L1 OUT. (See Fig. 2) Functional earth or screen cables may be terminated to the EARTH connection.

When using the sounder as a stand-alone unit, a cap is available (red cap part no 45681-293 or white cap

part no 45681-292) and is secured with a 1.5mm, AF hexagon socket head screw. A hexagonal driver (part

no 29600-095) is available from Apollo. The isolator LED can be seen through the moulding as shown in Fig 2.

Technical Data

Operating voltage

Sounder output

High tone setting volume

Low tone setting volume*

Sound pressure level information published in document PP2203 and isolator

operation information published in document PP2090, both available on request

Current consumption at 24V DC

quiescent

switch-on surge

sounder VAD operating

VAD frequency

IP rating

*Low tone setting does not comply to EN54–3 and should not be used for ﬁ re

alarm applications