Apollo Valves 61YLF-20-T1 Series 설치, 운영, 유지보수 매뉴얼 - 페이지 2

{카테고리_이름} Apollo Valves 61YLF-20-T1 Series에 대한 설치, 운영, 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Apollo Valves 61YLF-20-T1 Series 4 페이지. Bronze swing check valve

페이지 인쇄
®
APOLLO
BRONZE SWING CHECK VALVE IOM GUIDE
INTRODUCTION
The Apollo Bronze Swing Check valves covered in these guidelines are Class 125, Class 150 & Class 300
bronze, metal seat and soft seat valve types. Check Valves are used in piping systems where flow in one
direction is desired. Arrow on side of valve indicates flow direction. If backflow occurs in the system the
swing check disc will close onto sealing surface of body not allowing the flow to reverse.
SERIES
MODEL
61Y-09x-01
161S
61Y-19x-01
161T
61Y-20x-V1
162T
61Y-20x-T1
163T
61Y-10x-T1
163S
61Y-21x-01
164T
61Y-75x-01
168T
61Y-75x-T1
169T
61YLF-09x-01
161S-LF
61YLF-19x-01
161T-LF
61YLF-20x-V1
162T-LF
61YLF-20x-T1
163T-LF
61YLF-10x-T1
163S-LF
Table 2 Pressure Ratings
Saturated Steam
Cold Water
Saturated Steam
Cold Water
Saturated Steam
Cold Water
These ratings are the maximum allowable, non-shock pressures at the temperatures shown and
allowable pressures may be interpolated between temperatures shown. Use of a pressure rating at a
material temperature other than the temperature of the contained fluid is the responsibility of the user,
and subject to the requirements of applicable codes. The safe pressure-temperature rating of a solder
joint valve is dependent on the composition of the solder used. All valves are 100% pneumatically shell
and seat tested at a pressure of 80 psi in accordance with MSS-SP-80 Manufacturers Standardization
Society requirements.
Swing Check 61Y ES 1498 a.pdf.doc
Class 125 Bronze Disc, Solder end connection, Y-pattern
Class 125 Bronze Disc, NPT end connection, Y-pattern
Class 125 Viton Disc, NPT end connection, Y-pattern
Class 125 PTFE Disc, NPT end connection, Y-pattern
Class 125 PTFE Disc, Solder end connection, Y-pattern
Class 150 Bronze Disc, NPT end connection, Y-pattern
Class 300 Bronze Disc, NPT end connection, Y-pattern
Class 300 PTFE Disc, NPT end connection, Y-pattern
Class 125 Lead Free Bronze Disc, Solder end connection, Y-pattern
Class 125 Lead Free Bronze Body & Disc, NPT end connection, Y-pattern
Class 125 Lead Free Bronze Body, Viton Disc, NPT end connection, Y-pattern
Class 125 Lead Free Bronze Body, PTFE Disc, NPT end connection, Y-pattern
Class 125 Lead Free Bronze Body,PTFE Disc, Solder end connection, Y-pattern
Class 125
125 psi (8.6 Bar) to 353°F (178°C)
200 psi (13.8 Bar) at 100°F
Class 150
150 psi (10.3 Bar) to 366°F (185°C)
300psi (20.7 Bar) at 100°F
Class 300
300 psi (20.7 Bar) to 423°F (217°C)
1000psi (68.9 Bar) at 100°F
5
4
6
3
1
7
MATERIAL
ITEM DESCRIPTION
Class 125 & 150
Class 300
1
PLUG
ASTM B16
ASTM B16
2
CAP
ASTM B62
ASTM B61
3
DISC
ASTM B62
ASTM B61
4
HANGER
304 SS
304 SS
5
PIN, HANGER
304 SS
304 SS
6
NUT
ASTM B16
ASTM B16
7
BODY
ASTM B62
ASTM B61
Type 3 Swing Check Valve
DESCRIPTION
2
5
4
6
3
7
8
9
QTY
ITEM DESCRIPTION
Class 125 & 150
1
1
PLUG
ASTM B16
2
CAP
ASTM B62
1
1
3
DISC
ASTM B62
1
4
HANGER
304 SS
1
5
PIN, HANGER
304 SS
1
6
NUT
ASTM B16
1
7
BODY
ASTM B62
8
SEAT
PTFE
9
WASHER
ASTM B16
Type 4 Swing Check Valve
1418 S. Pearl Street Pageland SC USA 29728
2
4
Page 2 of
2
MATERIAL
QTY
Class 300
ASTM B16
1
ASTM B61
1
ASTM B61
1
304 SS
1
304 SS
1
ASTM B16
2
ASTM B61
1
PTFE
1
ASTM B16
1