Data Harvest EASYSENSE V-Log 사용자 설명서 - 페이지 15
{카테고리_이름} Data Harvest EASYSENSE V-Log에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Data Harvest EASYSENSE V-Log 17 페이지.
페이지 인쇄
EASYSENSE V-Log User Guide
Using the on-screen keypad
Enter Password:
DHG2020
abcdefghijklmnopqrstu
vwxyzABCDEFGHIJKLMNOP
QRSTUVWXYZ0123456789
+-^%$@!_:\/?<=>.[]
Connecting a group of iPads/Androids to a V-Log
It is possible for a group of devices to connect to one V-Log WiFi simultaneously to allow students to work
collaboratively on a single experiment.
Note: Performance maybe impacted if lots of devices are connected to the same logger.
When connecting to V-Log, the first iPad/Android/Windows PC to connect is given 'control' of the logger
and will therefore be able to setup, start and stop the experiment. All subsequent devices that connect to
the logger are given 'Viewer' status, they will see the set up changes made by the controller, and as data
is captured it will appear in real time.
When recording stops, all iPads/Androids automatically save the captured data into their internal memory.
One iPad/Android cannot change or delete the data held on another iPad/Android.
To leave a group, simply tap on the connection status button to disconnect (iPad users this is bottom right
of the screen, Android users top right of the screen).
When the controlling iPad/Android disconnects this will disconnect all the others. A new controlling
iPad/Android is chosen by ensuring that it is the first to re-connect.
WiFi Specifications
V-Log WiFi is a wireless enabled data logger. It is classed as a mobile device and has a usable
transmission range of 0.2 m to 10 m in open air.
V-Log WiFi loggers produced prior to April 2016 are compatible with IEEE 802.11b.
V-Log WiFi loggers produced after April 2016 are compatible with IEEE 802.11n.
Supports WPA-Personal (TKIP) and WPA2-Personal (AES) Security (802.11i)*
Frequency Range: 2412-2462 MHz
Channels supported: 1 to 11
*V-Log WiFi will automatically detect and use the required security protocol.
Hereby, Data Harvest Group Ltd., declares that V-Log WiFi is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
A full copy of the Declaration of Conformity can be obtained by writing to the following address:
Data Harvest Group Ltd., 1 Eden Court, Leighton Buzzard, Bedfordshire, LU7 4FY, UK.
V-Log in Bluetooth mode
If V-Log has a Bluetooth board fitted it can be used in Bluetooth mode. If using V-Log battery powered in
this mode, fully charge the battery before use e.g. leave to charge overnight for use in lessons the next
day. When the battery is in good condition and fully charged it will power a Bluetooth connected V-Log for
about 8 hours.
Note: V-Log stays awake while Bluetooth is turned on. Disconnect after use as the battery will continue to drain if V-
Log is stored with Bluetooth still selected.
Ensure the firmware of V-Log is at least V1.9 or higher.
Do NOT pair the devices (when paired V-Log will not be made available to the EasySense software).
Data Harvest Group Ltd, 2014
Use
&
buttons to go forward or back through the alphabet /
numbers / symbols on the keyboard.
Use
to select / accept the symbol under the dark cursor.
Use
to delete a character.
Move the cursor to the 'tick' symbol and press
entered password.
Move the cursor to the 'cross' symbol and press
screen with any characters entered to be rejected and ignored
15
DS133 (5)
to accept the
to leave this
.