DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 운영 매뉴얼 - 페이지 17

{카테고리_이름} DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 18 페이지.
DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010에 대해서도 마찬가지입니다: 운영 매뉴얼 (18 페이지), 운영 매뉴얼 (18 페이지), 운영 매뉴얼 (19 페이지)

페이지 인쇄
DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 운영 매뉴얼
1.1.3

Developer-level

L
C
P
Min
Bartack
d
00
01
0
Thread trimmer
02
00
0
d
Seam ways
d
07
00
150
d
07
01
1
Motor
d
08
00
1
d
08
01
1
d
08
02
0
d
08
10
0,1
d
08
11
1
d
08
12
0,1
d
08
13
0,1
d
08
14
1
d
08
20
0
d
08
21
0
d
08
22
0
d
08
23
0
d
08
30
0
d
08
31
0
d
08
32
0
d
08
40
0
d
08
41
0
d
08
42
0
d
08
43
0
d
08
44
0
d
08
50
0
d
08
51
0
d
08
52
0,1
d
08
53
0,1
d
08
54
1
d
08
55
0
Thread tension
d
09
01
5
Machine run blockage
d
50
00
0
d
50
01
0
© 2010 Dürkopp Adler AG
Max
Preset
Unity
359
75
°
360
170
-
9999
1500
rpm
20
6
Stitches
9999
5000
rpm
100
40
rpm/ms
50
4
Kgcm²
100,0
1,5
Ohm
200
3
mH
100,0
21,0
V/1000rpm EMK
20,00
11,00
A
10
2
-
255
64
-
255
64
-
255
0
-
255
24
-
255
0
-
255
1
-
255
6
-
255
112
-
255
58
-
255
32
Inc
1000
0
2,857°
1000
16
Inc
1
0
-
1
0
-
99,99
5,00
-
99,99
5,00
-
9999
900
s
2000
180
rpm
100
10
%
1
0
-
1
0
-
Description
Mechanical switching angle of th e bartack
The FA speed shall angle be reached before switching on
the magnets.
Speed limitation for seam ways
Stitches for the speed limitation by seam ways
Maximum motor speed
Maximum acceleration or deceleration
Mechanical inertia
Stator resistance
Stator inductance
Maximum stator current
Pole couple number
Factor K
of the speed control
pn
Factor K
of the speed control
in
Factor K
of the speed control
dn
Pre control of the speed control in the breaking sequence
Factor K
of the distance control
ps
Factor K
of the distance control
is
Factor K
of the distance control
ds
Factor K
of the position control
px
Factor K
of the position control
dx
Increments for the add-on connection of the PD situation
control system
Angle to the positioning
Increments for the position speed
Choice of the pedal
0 = Analogous;
1 = Digital
endurance test active
0 = No;
1 = Yes
Period motor on
Period motor off
Period oft the endurance test
Speed for the reference drive
Pulse duty ratio at the on threading help
Machine run blockage
0 = off;
1 = on
The mode of operation from machine run blockage switch
0 = NC;
1 = NO
II-17
Operating manual part II