Cavity Sliders CL100 Mortice Lock 피팅 지침
{카테고리_이름} Cavity Sliders CL100 Mortice Lock에 대한 피팅 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Cavity Sliders CL100 Mortice Lock 3 페이지. Fitting instructions
페이지 인쇄INDICATOR LOCK Fitting Instructions
NOTE: Please read instructions before drilling any
holes or marking out hole centres.
Mark both sides of the door using the template (flip
template over to mark other side).
DO NOT drill right through the door as alignment
issues will occur. Only drill to centre.
There are five stages to fitting the Mortice Case:
Stage 1: Mark drilling positions for lock case.
Stage 2: Mark drilling positions for door furniture to
be installed
Stage 3: Prepare door by mortising and drilling holes.
Stage 4: Fit lock & door furniture.
Stage 5: Fit striker.
Stage 1 - Mark Drilling Positions
for Lock Case
1. Mark chosen height of lock on face of door.
Height is normally measured to centre of square
spindle (Hole 9).
2. Mark 'Height Line' at top of template 57.5mm
(2-9/32") above Hole 9 or 121.5mm (4-25/32") above
Hole 10 on front edge and both faces of door.
3. Make a vertical centre line on front edge of door.
Front
edge
of
door
Centre
H E
line
7
Ø
( 2
1
m
6 . 5
m
Ø
4 x
)
/ 4 "
( 1
2
3
4
5
6
t 5
s e
c k
B a
8
G
I N
I L L
R E
D R
4. Align top edge of template with height line and
arrows to vertical centre line.
5. Mark universal hole positions (Holes 1-8) for lock
case using a sharp nail or pencil.
Universal Hole Positions
Hole #
Hole Diameter
1 - 6
19mm
7 & 8
2.5mm
3/32"
1
Height
line
E
A T
P L
M
T E
R
K E
R I
S T
E
L I N
H T
1 6
I G
1 4
1 2
m
6
m
)
4 "
m
5 /6
1 0
m
)
(1
4 "
5 / 6
1 5
1 2
9
1 2
1 3
1 2
1 0
2 5
A 5
0 Z
1 1
1 0
C L
1 8
. 2 0
0 2
C E
T I
O R
)
4 "
0 M
3 / 6
N S
1 0
- 1
C L
I O
( 2
C T
R
F O
R U
m
6
m
E
S T
A T
I N
P L
N G
M
T I
T E
F I T
A D
Depth
3/4"
77mm
3"
25mm
1"
Stage 2 - Mark Drilling Positions
for Door Furniture
1. Highlight correct drilling options required
for handle and use a sharp nail or pencil to
mark required hole centres. Holes 12-13 to be
vertical or diagonal fixing holes at the correct
hole centres to suit the lever handles being
used.
Indicator Lock Hole Positions
Hole # Hole Diameter
Depth
9 - 11
19mm
3/4"
To Centre of Door
12 or 13 6.5mm
1/4"
To Centre of Door
10mm
25/64" To Centre of Door
14 & 15
Stage 3 - Mortice & Drill Holes
DO NOT drill right through the door.
Alignment issues will occur. Drill to centre on
both sides for through holes. Check Stage 2
chart for hole depth.
1. Drill Holes 1-6. Make sure drilled holes are
straight and level.
2. Chisel out remaining wood between holes indicated
in shaded area on template to create a slot.
Note: Maximum slot length not to exceed 134mm
(5-9/32").
3. Drill Holes 7 and 8.
4. Remove face plate from lock case and temporarily
screw lock case in place. Mark around outside edge
of inner forend then remove lock.
5. Router out marked area to a depth of 7mm (9/32").
Important: Recess of front section must be routered
flat and even. Long term damage will occur if not
done correctly.
6. Drill Holes 9 to 11.
7. Remove remaining wood from oval shaped slot
between Holes 10 and 11.
8. Drill holes for fixing handles using marks from
Stage 2.
Inner
forend
Face
plate
2
Door Side
Both
Both
Both
3
Drilled
holes
7 & 8
Router
out 7mm
(9/32")