Durston Tools 2L 지침
{카테고리_이름} Durston Tools 2L에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Durston Tools 2L 2 페이지. Pro ultrasonic cleaner
페이지 인쇄WHAT ITEMS CAN I CLEAN IN MY ULTRASONIC?
Ultrasonic cleaners are suitable for cleaning a wide variety of materials, including metals,
glass, rubber, ceramics and some hard plastics. An ultrasonic cleaner is especially useful for
removing tightly-adhered contaminants from intricate items with blind holes, cracks and
recesses. The following is a list of example items that are suitable for Ultrasonic Cleaning,
Please note that the below list is not an exhaustive list of items that can be cleaned.
Gold, Silver and Platinum Jewellery Necklaces, Bracelets, Rings, Precious Stones, Watch
Casings and Straps. Please seek specialist advice on some stones.
UNSUITABLE ITEMS
The following is a list of items that are not suitable for Ultrasonic Cleaning:
•
Soft Jewellery: Pearls, Emerald, Ivory, Coral, Agate, Sea Turtle Shells etc
•
Welded, Plated and Glued Items
•
Watches: Except divers watches with a depth rate of over 50m (150ft)
•
Other: Porous, Ceramic items or with pre-existing cracks or damage.
•
This is not an exhaustive list but an indication – please exercise care and build your
experience.
ADDITIONAL NOTES
When the required temperature is reached the heater will turn off. If ultrasonic mode is
still on, the temperature may rise slowly until the ultrasonic cycle is complete, this is due
to additional heat from the transducers - it will be affected by the amount of material being
cleaned.
At the end of the cycle turn the machine off and allow a period of 5-10 minutes before
using again. The maximum period for the Usonic cycle is 60 minutes. This prolongs the
working 'life' of the unit.
Using the Basket will allow a 'Gentle' cavitation cleaning action.
Suspending items in the tank without using the basket will allow a much more
vigorous cleaning action BUT do not allow any item to rest on the floor of the tank as
this can cause transducer damage.
Please note that the liquid capacity of the tank is to the internal line / indent on the inside
of the tank wall .
The Size in the product tital indicates the overall size of the machine. Liquid capacity is
indicated below.
Model
Tank Capacity
Cleaning Power
2L
1500ml
60w
3.2L
2500ml
120w
4.5L
3500ml
180w
[email protected] | www.durston.com
Heating Power
Frequency
100w
40 kHz
200w
40 kHz
300w
40 kHz
PRO ULTRASONIC CLEANER
INSTRUCTIONS
2L, 3.2L & 4.5L MODELS
IMPORTANT INFORMATION - PLEASE READ BEFORE USE
•
Ensure that you are familiar with all procedures before using your Durston Ultrasonic
Cleaner. Please read all of the operating instructions in this booklet.
•
Do not run continuously. Run for a maximum of 60 Minutes.
•
Do not over-fill the machine, let it overflow or allow liquids to run down the side of the
machine, always disconnect from the power before emptying.
•
Do not turn the unit on while it is empty, this will cause damage and void your warranty.
•
Ensure that the power supply is disconnected once the cleaning sequence is
complete and before emptying the tank.
•
Only operate in a clean and dry environment and ensure that your Ultrasonic Cleaner
is on a hard, flat surface so that the air vents are not obstructed.
•
Do not operate with wet hands.
•
Do not put your hands into the tank while the cleaning sequence is in progress.
•
Do not allow any item to rest on the floor of the tank when unit in Usonic mode.
•
Only use water-based cleaning solutions in the tank, do not use anything flammable
or corrosive.
•
Once the cleaning sequence has been completed, always empty the tank and wipe
with a clean and dry cloth.