Dust Free 06159 설치 및 운영 매뉴얼 - 페이지 3

{카테고리_이름} Dust Free 06159에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dust Free 06159 9 페이지. 21", 33", 45" ultraviolet light systems

페이지 인쇄

BIO-FIGHTER® 4XTREME INSTALLATION & OPERATION MANUAL

INSTALLATION GUIDELINES

This device installs on the air handling system.

Installation location must be at least 12" wide

and deep enough to allow a minimum of 1"

clearance at the tip of the lamp when installed.

Allow sufficient clearance in front of the device

to remove the lamp.

120V or 240V power must be available at the

installation location. Hard-wire device to electri-

cal service in accordance with NEC.

SIZING & PLACEMENT

Use a lamp length that covers the largest area

of the coil while maintaining a minimum clear-

ance of 1" from coil. and duct. Lamp should

not touch or be closer than 1" to any surface

along the length of the lamp. For coil disinfec-

tion applications, install the device no closer

than 1" from coil.

IMPORTANT:

The 4Xtreme 45" should not be in installed in

applications where air flow velocity exceeds

3,000 FPM. Lamp breakage may occur.

For optimum coil and drain pan disinfec-

tion efficiency, the following placement

guidelines are recommended.

Each foot of lamp length irradiates:

1 sq. ft. of coil area when installed 1"-2" from coil.

2 sq. ft. of coil area when installed 3"-6" from coil.

3 sq. ft. of coil area when installed 7"-12" from coil.

CAUTION

Professional Installation Only.

Only a qualified technician should install and main-

tain UV-C lighting or service equipment in which it

is installed. Improper installation could cause

human injury or equipment damage. Always dis-

connect electrical power prior to any HVAC mainte-

nance. THIS INCLUDES FILTER MAINTENANCE.

SPECIAL UV-C INSTALLATION NOTES

• Do not install in closet return grille applications.

• Do not expose wiring or plastic parts to UV-C light.

• Do not install where UV-C light can be seen

after installation.

• Do not install beneath a humidifier.

• If the UV device is installed on the inlet side

(return air side) of a coil, make sure that the

HVAC system is configured such that the

blower is located between the return air filter

and the inlet side (return air side) of the coil,

such as would be found in a traditional up-

flow, or horizontal furnace with the coil

placed after the heat exchanger.

• If the UV device is installed near an air filter,

check with filter manufacturer for UV-C

resistance properties.

• If the desired UV installation location is

intended to irradiate an air filter, to neutralize

the microbiological matter on the air filter

surface, such as would be found in the

return air drop of a basement application or

in the return plenum of a horizontal system

in an attic; take precautions as described in

note above, and make sure the UV fixture is

placed on the return side of the filter. DO

NOT INSTALL THE UV FIXTURE ON EITHER

SIDE OF THE FILTER IN HALL / CLOSET

RETURN AIR APPLICATIONS.

TION! Warning sheet #212945-00).

TROUBLESHOOTING

Maintenance and troubleshooting should be

performed by a qualified technician.

Device fails to operate.

1. Check proper power is being supplied to

the device, and that the switch lights when

unit is turned on.

2. Check that the lamp connector is securely

attached to the lamp.

3. Check that ballast is receiving correct

power. Replace ballast if necessary.

4. Check continuity of lamp filaments.

(Replace lamp if necessary.)

5. Check that wires are properly connected

to lamp and ballast.

(See ATTEN-