Dust Right Downdraft Table 조립 지침 - 페이지 4

{카테고리_이름} Dust Right Downdraft Table에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Dust Right Downdraft Table 4 페이지.

페이지 인쇄

Assembly

1. Turn over the Case (1) so the bottom is facing up.

2. Thread the Leveling Feet and Adjustment Nuts (2) into

the holes on the Case (1). You will fine-tune and secure

the height of the Leveling Feet and Adjustment Nuts

once you place the unit in its final location.

3. From inside the Case, insert the Dust Port (3) in the

hole in the rear of the Case and align the mounting

holes in Dust Port's flange with the holes in the rear

of the Case. Secure with the four Small Pan-Head

Screws (14) through the Case and into the tapped

holes in the Dust Port's flange. Do not fully tighten

until all the screws are installed.

4. Attach the Right Edge Lip (4), Left Edge Lip (5) and

Rear Edge Lip (6) to the Case (1) with three Lock

Knobs (10) in each. Make sure that the folded edges

of the Right and Left Edge Lips face outward and

that the rounded corners are at the front of the unit.

The Right and Left Edge Lips can be raised and lowered

and the Back Edge Lip removed to accommodate

workpieces of different sizes.

5. Attach the Handles (9) to the sides of the Case (1),

using two Large Pan-Head Screws (13) for each handle

6. If they're not already in place, fit the flexible Rubber

Grommets (8) into the large holes in the Downdraft

Plates (7). Place the Downdraft Plates in position

on the Base (1).

7. Thread the Stopper Nuts (12) onto the Stopper

Bolts (11). You will insert these in the Rubber

Grommets in the Downdraft Plates to hold smaller

workpieces and keep them from shifting.

8. Attach a 4" dust hose with hose clamp (not included)

or other fitting to the Dust Port.

9. Place the unit where it will be used and adjust the

Leveling Feet (2) as needed.

Holding your Workpiece

The Right and Left Edge Lips (4 and 5) can be raised

or lowered and the Back Edge Lip (6) removed to

accommodate a variety of workpiece sizes, and the Stopper

Bolts (11) and Nuts (12) can be used as a sort of bench dog

to keep workpieces from shifting.

1. To use the Stopper Bolts (11) and Nuts (12) to hold

a workpiece while you're working on it, place the

workpiece on the Downdraft Table and insert Stopper

Bolts in the appropriate smaller holes in the Downdraft

Plates. Fig. 1. Remove the workpiece, carefully lift the

Downdraft plates and, from underneath, thread a

Stopper Nut onto each Stopper Bolt. Then reinstall

the Downdraft Plates in the Case.

2. If your workpiece won't fit within the Downdraft Table,

you can lower the Right and Left Edge Lip (4 and 5) and

57664

Rev 12/17

Fig. 1

Fig. 2

remove the Back Edge Lip by loosening the Lock

Knobs (10), making the adjustments and retightening

the Lock Knobs.

Storing your Downdraft Table

1. Identify a wall location with enough space to fit the unit.

Lag bolt must be driven into a wall

stud to be able to support the weight of the Downdraft

Table. Failure to do so could result in the Downdraft

Table crashing down, potentially causing property

damage and/or personal injury.

2. Drill a pilot hole and drive a 3/8" x 4" lag bolt (not

included) into a wall stud. Make sure that the lag bolt

is secure in the wall stud but also extends far enough

from wall to account for the Leveling Feet.

3. Place the three Downdraft Plates (7) vertically inside

the Case (1) for storage and hang the unit on the lag

bolt, using the keyhole in the Case bottom. Fig. 2.

Check Rockler.com for updates. If you have further questions, please

contact our Technical Support Department at 1-800-260-9663

or [email protected]

Distributed by Rockler Companies, Inc.

Medina, MN 55340