Datalogic 952001321 사용 설명서

{카테고리_이름} Datalogic 952001321에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Datalogic 952001321 7 페이지. Contrast sensor

페이지 인쇄

This product is covered by one or m ore of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-PA/MA...W

Contrast sensor

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED

The yellow LED on indicates that the N.O. (normally open) output status

is closed.

READY LED

The green LED indicates a normal operating function.

If the green LED flashes, the acquisition has failed.

Please refer to the "SETTING" paragraph for setup procedure

indications.

SET PUSHBUTTON

A long pressure on the pushbutton activates the self-setting procedure.

INSTALLATION

S5N-PA...W : The sensor can be fixed by means of the M18x1 threaded

body through a  18 mm hole, using the specific washer and the

enclosed 24 mm nuts (maximum torque of tightening 1.5 Nm).

Alternatively, the sensor can be mounted through the two housing's holes

using two screws (M3x22 or longer) and nuts.

Amongst the various possible solutions, we suggest to choose the

combination that offers the best visibility of the signalling Leeds and the

easiest access to the SET pushbutton.

22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available to

guarantee an improved torque.

S5N-MA...W : The sensor can be fixed by means of the M18x1 threaded

body through a  18 mm hole, using the two CH.24 nuts enclosed (22

Nm maximum tightening torque).

For both plastic version and metallic version are available various

orientable fixing brackets to ease the sensor positioning (please refer to

the accessories listed in the general catalogue).

The operating distance is measured from the front surface of the sensor

lens.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

BROWN

10 ... 30 Vdc

WHITE

N.C. OUTPUT

BLACK

N.O. OUTPUT

BLUE

0 V

S5N-PA VERSION

S50-PA VERSIONS

81.5

14.5

1.5

3.5

CABLE VERSION

2.5

SET PUSHBUTTON

N°.2 Ø3.8

READY L ED

STABILITY LED

OUTPUT LED

TECHNICAL DATA

S5N-PA PLASTIC VERSIONS

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Jitter

Indicators:

Setting:

Operating mode:

Data retention:

Operating temperature:

Storage temperature:

Insulating strength:

Insulating resistanc e:

Operating distance (typical values):

Minimum spot dimension:

Emission type:

Ambient light rejection:

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

Vibrations:

Shock resistance:

Housing:

Lenses:

Mechanical protection:

Connections:

Weight:

75 g. max. cable vers.

25 g. max. connector vers.

AtEx 2014/34/EU

Emission:

M12 CONNECTOR

N.C. OUTPUT

(WHITE)

0 V

(BLUE)

DIMENSIONS

S5N-MA VERSION

S50-MA VERSIONS

14.5

2.5

SET PUSHBUTTON

READY L ED

STABILITY LED

READY L ED

STABILITY LED

OUTPUT LED

S5N-MA METALLIC VERSIONS

10 ... 30 Vdc (limit values)

2 Vpp max.

25 mA max.

N.O. and N.C.; PNP or NPN; 30 Vcc max. (short-circuit protection)

100 mA max.

2 V max.

100  s

5 kHz

50  s

OUT PUT LED (YELLOW) / LED READY (GREEN)

SET pushbutton

LIGHT mode on N.O. output / DARK mode on N.C. output

non volatile EEPROM memory

-10 ... 55 °C

-20 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

10 mm 2 mm

4.5 mm

white light LED (400-700 nm)

according to EN 60947-5-2

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

PBT

Nickel plated brass

PMMA

IP67 Metal versions type 1 enclosure

2 m cable  4 mm / M12 - 4 pole connector

110 g. max. cable vers.

60 g. max. connector vers.

II 3D EX tc IIIC IP67 T 85°C

Exempt Risk Group (RG0) according to IEC 62471

EASY TOUCH

The sensor uses the patent-covered EASY TOUCH technology that

allows a rapid and safe self-setting of the product.

Two different setting possibilities are available:



- EASY TOUCH

; a long pressure of the SET pushbutton allows self-

10 ... 30 Vdc

setting.

- FINE DETECTION; to be used only in particularly critical conditions,

(BROWN)

this setting procedure is used only when the EASY TOUCH is not

N.O. OUTPUT

sufficient.

(BLACK)

Setting of S5N-PA/MA...W

To achieve a correct sensor functioning, the coloured mark or object to

be detected has to be placed at the right reading distance.



- EASY TOUCH

(standard detection in the DARK m ode)

The EASY TOUCH technology allows the functioning in the DARK

mode (mark presents a lower light intensity respect to the

background).

The mark to detect has to be placed correctly at the right reading

distance within the sensor spot.

Press the SET pushbutton until the READY LED turns OFF.

Release the SET pushbutton and wait for the READY LED to turn ON.

The sensor is now ready to detect the pre-set coloured mark or object

CABLE VERSION

(output LED turns ON when the N.O. output is closed).

- Fine detection (DARK or LIGHT m ode)

This mode offers an improved detection precision.

The sensor can function either in the DARK operating or in the LIGHT

operating mode (light-coloured mark on dark background).

The operating mode is selected automatically by the sensor.

READY L ED

STABILITY LED

OUTPUT LED

The mark to detect has to be placed correctly at the right reading

distance within the sensor spot.

Press the SET button until the READY LED turns OFF.

Hold the SET button until the READY LED turns ON (3s).

The sensor is acquiring the mark.

When the READY LED flashes slowly, position the background to

coincide with the sensor spot and press the SET button again.

If the READY LED lights up permanently, the acquisition has been

successful; if the LED flashes quickly, the acquisition has failed due to

insufficient contrast. Pressing the SET button returns the sensor to

the previous setting. Repeat the procedure from the beginning.

The output LED is ON and the N.O. output is closed, when the sensor

is positioned on the pre-set coloured mark.

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

T el: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions,

Support.

For information about the disposal of Waste Electrical

and Electronic Equipment (WEEE), please refer to the

website at www.datalogic.com.

RESERVED.  Without limiting the rights under copyright, no part of this

documentation may be reproduced, stored in or introduced into a retrieval

system, or transmitted in any form or by any means, or for any purpose,

without the express written permission of Datalogic S.p.A. and/or its

affiliates. Datalogic and the Datalogic logo are registered trademarks of

Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All

other trademarks and brands are property of their respective o wners.

Datalogic reserves the right to make modifications and improvements

without prior notification.

826000442 Rev.C

SETTING