CBC ZC-D2550EHA 사용 설명서 - 페이지 3

{카테고리_이름} CBC ZC-D2550EHA에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. CBC ZC-D2550EHA 5 페이지. Zc-oh2 tamper-resistant indoor/outdoor housing

페이지 인쇄

3) Install ZC Series Dome Camera

Note: Before installing the ZC series camera into the housing,

remove its front dome cover, plastic retaining ring and video

cable. Only the base of the camera will be installed into the

housing.

a) Place the camera base into the housing, making sure that the 4

power and video wires feed through the hole in the camera base.

b) Fasten the camera to the housing base.

For 2-4mm, 3-6mm and 4-9mm models: Use the supplied #6 X 1/2"

machine screws and spacers.

For 5-50mm models: Use the supplied #6 X 5/16" machine screws.

Spacers should not be used with this model.

c) Make the 4 wiring connections in accordance with the instructions

below.

4) Connect Power

Important: Make wiring connections only after it has been

determined that power has been disconnected. Failure to do

so could lead to permanent damage to the camera and void

the warranty. The ZC series cameras will accept either 12 Volts DC

or 24 Volts AC. If using 12VDC, be sure to determine the polarity

before connection. The Red wire connects to 12VDC (+) Positive ter-

minal and the Black wire connects to the Ground terminal. When using

12VDC, use only a regulated power supply with a minimum 300mA out-

put, (model C12DCR recommended). For 24VAC input, connect the

Red and Black wires to the 2 power input terminals.

5) Connect Video

Connect the White wire to the Video-Out Terminal and the Green wire

to the Ground Terminal as shown in Figure 1. Note: A BNC con-

nector (included) can be crimped on to the white and green

video signal wires using the supplied butt connectors. It is rec-

ommended these connections be crimped with a crimping tool

and covered with shrink tubing.

IRING

IAGRAM

LACK

HITE

REEN

12VDC+

24VAC

12VDC G

24VAC

ROUND OR

IDEO

IGNAL

IDEO

ROUND

Note: If necessary, needle nose pliers can be used to make power and

video connections.

Note: Special Focusing Instructions when using 5-50mm dome.

If the 5-50mm lens is set to a focal length of 20mm or greater, the dome

cover must be held in front of the lens while focusing to obtain proper

focus.

6) Install the Desiccant Pack

After the camera has been installed, attach the supplied desiccant pack

to the camera. Remove the desiccant pack from its storage bag.

Remove plastic from the double-sided tape and attach to the camera

bracket as shown in Figure 1. The desiccant pack is used to absorb any

moisture trapped inside the dome during installation. To avoid excessive

moisture buildup, it is recommended that the camera not be installed in

rainy or excessively damp conditions. The desiccant pack can be

replaced if condensation develops inside the housing.

7) Re-Install Dome Cover

Place the dome cover on the housing base. Push the cover lightly onto

the base and tighten the 3 tamper resistant screws until the cover seals

tight against the housing base. Caution: Do Not Over Tighten!

HANGING THE

OLYCARBONATE

The ZC-OH2 housing is supplied with a clear dome with painted slot as the

standard. In the event the dome is scratched or damaged or if a different

dome is required (tinted, gold or chrome), the dome can be replaced.

Remove the 4 retaining screws and washers on the inside of the dome

cover and remove the aluminum retaining ring. The dome can then be

removed. Due to a tight seal, some pressure may be required to the top of

the dome to break the seal. After installing the new dome, replace the

retaining ring and tighten the 4 screws and washers until the retaining ring is

flush with the adjacent surface.

Regulatory Notice, FCC Rules: Part 15 This device has been tested

and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

the interference will not occur in a particular installation.

OME